background image

Emptying the condensed
water container

The condensed water will be collected
in the condensed water container
unless the appliance has been fitted
with a drain hose (see "Installation").

Empty the condensed water
container after every drying
programme.

The

Empty out container

indicator light

will come on if the maximum level of the
condensed water container is reached.

The indicator light will go out when the
door is opened and closed again.

^

Holding the container firmly in both
hands, as shown, pull it out slightly
towards the right-hand side.

^

Hold the container with both hands
and carry it in a horizontal position.

^

Open the shutter and empty out the
water.

^

To replace the container, hold it at a
slight angle (as when removing it)
and push it in gently until you feel it
click into position.

,

Condensed water should not be

consumed. It could lead to health
problems for people and animals.

Condensed water can be put to
household use (e.g. in a steam iron or
humidifier). To ensure that any residual
particles of fluff in the condensed water
are removed before use, pass it
through a fine sieve or paper filter first.

Cleaning and care

21

Содержание T 8428 C





















































Отзывы: