background image

Problem

Possible cause

Remedy

The Clean out
airways 
indicator
light comes on.

This indicator light comes on
to warn you that the dryer is
not working efficiently.

Possible cause: The fluff
filters are clogged with fluff
or with detergent residues.

– Cleaning the fluff filters is

usually all that is required.
However, if the

Clean out

airways

indicator light

does not go out after you
have cleaned the filters,
then also check all the
possible causes
described under "The
drying process goes on
too long or even switches
off".

To switch off the indicator
light:

– Open and close the door.

The

Clean out airways

indicator light can be
deactivated (see
"Programmable functions").

The programme
stops.
The Clean out
airways 
indicator
light comes on.
The buzzer sounds.

See above for possible
causes and their remedies.

To switch off the indicator
light:

– Open and close the door.

– Switch the dryer off and

then back on again.

– Then start the programme

again.

– If the

Clean out airways

indicator light comes on
again, contact the Miele
Service Dept.

The Empty out
container 
indicator
light comes on.
The buzzer sounds.

The condensed water
container is full or there is
kink in the drain hose.

– Empty out the condensed

water container.

– Check the drain hose.

To switch off the indicator
light:

– Open and close the door.

Problem solving guide

29

Содержание T 8428 C





















































Отзывы: