Miele T 8428 C Скачать руководство пользователя

Страница: 9 / 52

Control panel

Low temperature button

Delicate fabrics are dried at a lower
temperature.

Drying level button

with indicator lights

Display

Delay start button

This button is used for:
- Selecting the duration of the

Timed drying

programmes

- Delaying the start of a programme

Buzzer button

An audible tone sounds at the end of
the programme.

Check lights

For a description of these lights see:
"Problem solving guide" / "After sales
service".

Start/Stop button

For starting the programme selected
and cancelling a programme once it
has started.
The indicator light flashes while a
programme is being selected and
then is on constantly when the
programme has started.

Programme selector

with indicator lights

Door button

Pressing this button will open the
door even when the dryer is
switched off at the mains.

I-On/0-Off button

For switching the dryer on and off.

Operating the tumble dryer

Содержание T 8428 C





















































Результаты поиска

Содержание T 8428 C

Отзывы:

Похожие инструкции для T 8428 C

Бренды по названию

Популярные бренды

Miele T 8428 C, Руководство по эксплуатации

Результаты поиска

Содержание T 8428 C

Отзывы:

Похожие инструкции для T 8428 C

Бренды по названию

Популярные бренды