Miele T 4888 C Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 60

background image

Installation site

,

Make sure the dryer door can be

opened without hindrance after
installation.

Room in which the dryer is located

Air taken in for use in the drying
process will be warm when it is
expelled from the rear of the dryer. This
expelled air heats up the air in the
room. It is therefore very important to
ensure that the room is adequately
ventilated, particularly if the dryer is
located in a small room. Otherwise
running times and energy consumption
could be increased.

Transporting the machine to its
installation site

When moving the machine you can
hold it by the lid where it protrudes to
the rear of the dryer.
To manoeuvre the dryer out of its
packing case to its installation site you
will also need to hold it by the front feet.

Aligning the machine

The machine must be perfectly level to
ensure safe and proper operation.

^

The screw feet can be adjusted to
compensate for any unevenness in
the floor.

,

The ventilation gaps in the plinth

must not be covered over as this
would prevent a sufficient intake of
air.
This tumble dryer is not suitable for
building under (due to its sloping
facia).

Before moving the machine again
(e.g. when moving house)

After each use a small quantity of
condensed water will collect in the area
around the pump. This water can run
out if the machine is tipped up when it
is being moved. It is a good idea to run
the

Cool air

programme for

approximately 1 minute before moving
the machine. Any remaining
condensed water will then be fed into
the condensed water container or out
through the drain hose.

Installation

41

«
...
39
40
41
42
43
...
»

Содержание T 4888 C





























































Отзывы:

Нет отзывов

Похожие инструкции для T 4888 C

Бренд: Makita Страницы: 7

Бренд: VALERA Страницы: 98

MEDC700VJ - 27in Centennial Series Electric Dryer Oxide

Бренд: Maytag Страницы: 24

Headlines HD7800

Бренд: Sunbeam Страницы: 9

Бренд: Rupes Страницы: 12

ARTIST BREEZE 1800W

Бренд: OBH Nordica Страницы: 24

Бренд: Morphy Richards Страницы: 6

Бренд: BOMANN Страницы: 24

Compact Mini Fryer

Бренд: Coopers of Stortford Страницы: 4

Бренд: Boekel Страницы: 2

Бренд: Belson Страницы: 2

Бренд: Morgan Страницы: 6

Бренд: Pepcare Страницы: 28

Бренд: Lang Страницы: 20

Бренд: JLA Страницы: 46

D30 Phase 7 Non-Coin

Бренд: JLA Страницы: 60

Бренд: Gourmet Maxx Страницы: 68

Бренд: Maytag Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды