Miele T 4888 C Скачать руководство пользователя страница 52

Страница: 52 / 60

Drying levels

You can alter the drying levels for the

Cottons

and

Minimum

iron

programmes.

SETTINGS

back

DRYING LEVELS

COTTONS ...

MINIMUM IRON ...

Select a programme and confirm your selection.

The bar chart shows you the setting.
The machine is delivered with a medium setting set as stan-
dard.

Damper

Drier

Set drying level for Cottons

Select the drying level you want and confirm your selection.

–

The programme duration will be shorter (Damper) or
longer (Drier).

Extending the cooling down time

The Cooling down phase which takes place before the end
of a programme can also be lengthened if required. This
makes the garments easier to handle.

The bar chart shows you the setting.
The machine is delivered with: 0 mins (normal cooling down
period) set as standard.

0 mins

18 mins

Set extended cool-down

Select the extended time you want (in 2 minute increments)
and confirm your selection.

–

The programme duration will increase accordingly.

–

You cannot extend the Cooling down time for the

Warm air,

Cool air, Woollens handcare, Smoothing

programmes.

Settings menu

Содержание T 4888 C





























































Результаты поиска

Содержание T 4888 C

Отзывы:

Похожие инструкции для T 4888 C

Бренды по названию

Популярные бренды

Miele T 4888 C, Руководство по эксплуатации

Результаты поиска

Содержание T 4888 C

Отзывы:

Похожие инструкции для T 4888 C

Бренды по названию

Популярные бренды