Miele T 4888 C Скачать руководство пользователя страница 53

Страница: 53 / 60

Airways indicator

Fluff should be removed after drying. The

Clean fluff filters

indicator will remind you to clean the filters when a certain
amount of fluff has collected in the filters. You can decide
at what level of fluff this reminder should be given.

You will have an idea of how often this should be done after a
few drying programmes.

Off

Clean fluff filters

does not appear

Non-sensitive =

Clean fluff filters

only appears when there is

a heavy build-up of fluff

Normal

= Factory default setting

Sensitive

Clean fluff filters

appears when there is only

a small build-up of fluff

A tick will appear beside the option to show that it has been
set.

SETTINGS

back

AIRWAYS IND.

Off

Non-sensitive

Normal

Select the option you want and confirm your selection.

Anti-crease

The drum will continue to rotate at intervals for one hour to
prevent laundry creasing, if you do not wish to remove it
immediately.

A tick will appear beside the option to show that it has been
set.
The machine is delivered with this option set to: on.

SETTINGS

back

ANTI-CREASE

Off

Select the option you want and confirm your selection.

Settings menu

Содержание T 4888 C





























































Результаты поиска

Содержание T 4888 C

Отзывы:

Похожие инструкции для T 4888 C

Бренды по названию

Популярные бренды

Miele T 4888 C, Руководство по эксплуатации

Результаты поиска

Содержание T 4888 C

Отзывы:

Похожие инструкции для T 4888 C

Бренды по названию

Популярные бренды