Miele PW 6065 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 72

background image

Washer/ Dryer Stack

Height:

Stacking kit with pull out shelf
66

15

/

16

" (1700 mm)

The Miele washing machine can be
installed as part of a washer-dryer
stack in combination with a Miele
tumble dryer. An appropriate stacking
kit* is required.

Installation of the stacking kit must be
performed by a Miele Service
Technician.

Reinstallation of the machine lid

When reinstalling the appliance lid,
check the firm fit of the cover at the rear
bracket for a safe transport of the dryer.

Installation on a base

The machine can be installed on an
open or closed steel base, or on a
concrete base. Concrete is
recommended.

^

Secure the two front feet of the
washer with the supplied retaining
clips when installing on a concrete
base.

^

Read the supplied Installation
manual.

Coin mechanism

The dryer can be equipped with a coin
mechanism*.

The reprogramming necessary for the
coin mechanism must be done by a
Miele Service Technician.

Empty the coin mechanism regularly.
Coins or tokens may get jammed.

Do not install devices to auto-
matically turn the washer off, e.g. a
clock timer.

* Available from your Miele dealer or

Miele.

Installation

48

«
...
46
47
48
49
50
...
»

Содержание PW 6065









































































Отзывы:

Нет отзывов

Похожие инструкции для PW 6065

Бренд: Jackson Страницы: 2

Бренд: Gorenje Страницы: 18

Бренд: Graco Страницы: 32

Бренд: V-ZUG Страницы: 76

Бренд: AEG Electrolux Страницы: 108

Бренд: Hoover Страницы: 33

Pico Power 7920

Бренд: Hozelock Страницы: 12

Бренд: Kärcher Страницы: 15

Бренд: Samsung Страницы: 52

WW60J426 Series

Бренд: Samsung Страницы: 56

Бренд: Samsung Страницы: 60

Бренд: Samsung Страницы: 60

Бренд: Samsung Страницы: 216

Бренд: Samsung Страницы: 64

Бренд: Samsung Страницы: 68

Бренд: Samsung Страницы: 248

Бренд: Samsung Страницы: 48

Бренд: Samsung Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды