Miele PW 6065 Скачать руководство пользователя страница 35

Страница: 35 / 72

Repairs to electrical appliances must only be carried out by a qualified and

trained person in accordance with local and national safety regulations.
Repairs and other work by unqualified persons could be dangerous. The
manufacturer cannot be held responsible for unauthorized work.

The following section will help you avoid placing a service call by identifying
issues you may encounter while operating the machine:

A wash program cannot be started

Issue

Possible fault

Solution

The display remains off.

The washer has no
power.

Possible fault

–

the washer is not
connected to the electrical
supply,

–

the circuit breaker has
tripped.

Upon selecting the
program "Spin" the
program does not start.

The instructions in
"Before using for the
first time" were not
followed.

Follow the instructions as
described in the "Before using
for the first time" chapter.

There is a fault
message in the display.

As long as an error
message is
displayed, a program
cannot be started.

–

Regard the display
messages.

–

Confirm by pressing the jog
shuttle.

The display is dark and
the "Start" light flashes
slowly.

The machine goes
into "Standby". The
display shuts off to
save energy.

Press any direct select button.
The Standby function will be
ended.

Frequently asked questions

Содержание PW 6065









































































Результаты поиска

Содержание PW 6065

Отзывы:

Похожие инструкции для PW 6065

Бренды по названию

Популярные бренды

Miele PW 6065, Руководство по эксплуатации

Результаты поиска

Содержание PW 6065

Отзывы:

Похожие инструкции для PW 6065

Бренды по названию

Популярные бренды