Miele PW 5065 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 64

background image

Hot water connection

Connecting the machine to a hot water
supply will lead to low electrical
consumption during hot water
operation. The hot water temperature at
the water faucet must not exceed 158°F
(70°C).
The water in single water lines from the
hot water source cools faster when not
in constant use. To heat the wash water
more electricity must be used. The
same conditions for the hot water as for
the cold water connection will then
apply.

^

Connect the hot water intake hose
(red mark) to the water faucet.

The connection of the machine to a
hot water line only, is not possible for
functional reasons.

If the washer is not to be installed for
hot water connection, the settings "Main
wash", "Pre-wash" and "Rinses" must be
adjusted respectively. The hot water
intake hose must be removed.

^

Select in "Settings - Supervisor level"
the respective options "cold".

The program times may be
extended.

^

Unscrew the hot water intake hose
(red mark).

^

Screw on the supplied stopper.

Installation

50

«
...
48
49
50
51
52
...
»

Содержание PW 5065

































































Отзывы:

Нет отзывов

Похожие инструкции для PW 5065

Бренд: V-ZUG Страницы: 8

Бренд: FRAM Страницы: 58

Бренд: Samsung Страницы: 40

WF16J9000K Series

Бренд: Samsung Страницы: 52

Бренд: Samsung Страницы: 44

WF16J9800K Series

Бренд: Samsung Страницы: 54

Бренд: Samsung Страницы: 44

Бренд: Samsung Страницы: 48

Бренд: Samsung Страницы: 44

Бренд: Samsung Страницы: 132

Бренд: Samsung Страницы: 40

Бренд: Reaim Страницы: 12

Бренд: Metos Страницы: 52

Бренд: Viking Страницы: 12

Бренд: Hanseatic Страницы: 70

Бренд: FULLER O’BRIEN Страницы: 28

Бренд: Zanussi Electrolux Страницы: 28

AdoraDish V6000

Бренд: V-ZUG Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды