Miele PW 5065 Скачать руководство пользователя страница 14

Страница: 14 / 64

The program will be locked
3 minutes after the program has
started when the washer is operated
with a coin mechanism. Canceling
or changing a program is no longer
possible.

Canceling a program

A program can be canceled any time
after a program has started.

Turn the program selector to "End".

The washer drains the wash water away
and the program is canceled.

Press the "Door" button.

Remove the laundry.

Close the door and start a new
program.

Changing a program

To change a program

A program change is not possible after
a program has started.

To select a different program, the
started program must be canceled.

Adjusting the temperature

Some programs allow you to change
the temperatures up to 5 minutes after
the start.

Press OK.

The temperature is highlighted.

To change the highlighted
temperature use the

+/–

buttons.

Confirm with "OK".

Adjusting the spin speed

Press OK until the spin speed is
highlighted. Adjust the spin speed
with the

+/–

buttons. Adjustment is

possible until the start of the final
spin.

Selection of the "Pre-wash" is not
possible after the program has started.

Using the washer

Содержание PW 5065

































































Результаты поиска

Содержание PW 5065

Отзывы:

Похожие инструкции для PW 5065

Бренды по названию

Популярные бренды

Miele PW 5065, Руководство по эксплуатации

Результаты поиска

Содержание PW 5065

Отзывы:

Похожие инструкции для PW 5065

Бренды по названию

Популярные бренды