Miele G 690 Скачать руководство пользователя страница 49

Страница: 49 / 80

Problem solving guide

With the aid of the following explana-
tory notes, minor faults can be cor-
rected without contacting the Miele Ser-
vice Department.

Any work on the electrical compo-
nents of the appliance should only
be carried out by a suitably quali-
fied and competent person in ac-
cordance with local and national
regulations. Unauthorised repairs
could be dangerous.

If, however, you are unable to correct
the problem, the Miele Service Depart-
ment should be contacted.

Faults/possible causes

The dishwasher does not start

– The door is not properly closed.

– The plug is not properly inserted.

– The fuse is defective/has blown.

White residue on cutlery and
crockery

– No salt in the salt reservoir.

Fill the salt reservoir with dishwasher
salt for reactivation - see section on
"Water softener".

– Salt reservoir lid has not been

screwed on properly.

– Not enough rinse aid.

Use a higher dosage setting - see
"Adding rinse aid".

The dishes are not cleaned.

– The dishes are incorrectly loaded.

– The correct amount of detergent was

not dosed - see “Programme chart”.

– The filters in the wash cabinet are

not clean - see “Cleaning and care”.

– The spray arm jets are blocked - see

“Cleaning and care”.

– The wrong programme was selected

- see "Programme chart".

Water in the wash cabinet at the end
of a programme

– The outlet hose is kinked.

– The drain pump is blocked – see

“Cleaning and care”.

– Foreign bodies are obstructing the

non-return valve - see "Cleaning and
care".

Before removing the obstruction:

Press the START/Stop button for at
least one second.
All indicator lights next to the pro-
gramme selector buttons light up.

Switch off the dishwasher with the
ON/OFF switch.

Problem solving guide

Содержание G 690

















































































Результаты поиска

Содержание G 690

Отзывы:

Miele G 690, Руководство по эксплуатации, Страница: 49 / 80

Результаты поиска

Содержание G 690

Отзывы: