Miele G 690 страница 66 Скачать руководство пользователя

Страница: 66 / 80

3. Fitting the facia panel

The facia panel is delivered separately in the colour ordered with the necessary
accessories. It has to be fitted to the dishwasher when it is being installed.

Put the large cap

on the button for

the ON/OFF control switch.

Put the two small caps which have
one straight side

on to the "

and

"–" button switches. The straight
sides must face each other.

Put the 12 small oval caps

on to

all the other button switches

Place the seal supplied

in the

groove round the ventilation grille

Push the ventilation grille

into posi-

tion.

Place the facia panel

in position

and screw into place from the inside
using the six screws

For Information:

If the machine is equipped with the Info-
Control unit:
– first fit the transmitter
– then fit the facia panel.

Fitting instructions are supplied with the
transmitter.

Installing integrated “i” Dishwashers

Содержание G 690

















































































Результаты поиска

Содержание G 690

Отзывы:

Похожие инструкции для G 690

Бренды по названию

Популярные бренды

Miele G 690, Руководство по эксплуатации

Результаты поиска

Содержание G 690

Отзывы:

Похожие инструкции для G 690

Бренды по названию

Популярные бренды