background image

HYB-1000 KIT

The  HYB-1000  uses  six  AA,  1.5-volt  batteries  (alkaline 

recommended)  to  allow  testing  of  batteries  down  to  1  volt 

and supply power while the menu is active. The analyzer can 

test batteries down to 5.5 volts when the internal batteries are 

not functioning. 

Battery Power Indicator

The square in the upper left corner of the display indicates the 

charge level of the battery pack. The square is black when the 

battery pack is fully charged. It gradually changes to white as 

the charge level declines. The HYB-1000 will display a warning 

message when the batteries need replacing.

Full

Powered 

by test 

battery

Decreasing

Low

Replacing the HYB-1000 Batteries

1. Turn the HYB-1000 face down.

2. Remove the screw.

3. Press gently on the ridges above the arrow on the battery

compartment cover.

4. Slide the cover in the direction of the arrow and remove

the cover.

5. Remove the discharged batteries.
6. Insert new batteries as shown in the figure (right). Make

sure  the  positive  and  negative  terminals  are  positioned

correctly.

7. Insert the battery door tabs into the slots on the analyzer

and slide the door closed, making sure the latch locks.

8. Insert and tighten the screw.

Latch

Press 

here

Slide in 

this direction

Screw

Chapter 10: HYB-1000 Internal Batteries

Содержание HYB-1000


























Отзывы: