Midea MFA3T-96CRN1 Скачать руководство пользователя страница 95

Страница: 95 / 111

MCAC-UTSM-201707 Midea R410A T3 50Hz Top-discharge Series

1.4 Operating the remote controller

1) Install / Replace Batteries

The Remote Controller uses two alkaline dry batteries (R03/Ir03X2).

※

To install batteries, slide back the cover of the battery compartment and install the batteries

according to the directions (+ and -) shown on the Remote Controller.

※

To replace the old batteries, use the same method as mentioned above.

Notes:

1. When replacing batteries do not use old batteries or a different type battery. This may cause the

remote controller to malfunction.

2. If you do not use the remote controller for several weeks remove the batteries. Otherwise battery

leakage may damage the remote controller.

3. The average battery life under normal use is about 6 months.

4. Replace the batteries when there is no answering beep from the indoor unit or if the Transmission

Indicator light fails to appear.

2) Automatic Operation

When the Air Conditioner is ready for use, switch on the power and the

OPERATION

indicator

lamp on the display panel of the indoor unit starts flashing.

※

Use the

MODE

select button to select AUTO.

※

Push the

TEMP

button to set the desired room temperature. The most comfortable

temperature settings are between 21

°C

and 28

°C

※

Push the

ON/OFF

button to start the air conditioner. The

OPERATION

lamp on the display

panel of the indoor unit lights. The operating mode of AUTO FAN SPEED is automatically

set and there are no indicators shown on the display panel of the remote controller.

※

Push the

ON/OFF

button again to stop the unit operation.

Notes:

1. In the AUTO mode, the air conditioner can logically choose the mode of COOL, FAN, HEAT and DRY

by sensing the difference between the actual ambient room temperature and the set temperature on the

remote controller.

2. If the AUTO mode is not comfortable for you, the desired mode can be selected manually

3) COOL, HEAT, and FAN ONLY Operation

※

If the AUTO mode is not comfortable, you may manually change the settings by using

COOL, DRY, HEAT (HEAT PUMP units only), or FAN ONLY modes.

Содержание MFA3T-96CRN1
















































































































Результаты поиска

Содержание MFA3T-96CRN1

Отзывы:

Бренды по названию

Популярные бренды

Midea MFA3T-96CRN1, Техническое и сервисное руководство

Результаты поиска

Содержание MFA3T-96CRN1

Отзывы:

Бренды по названию

Популярные бренды