MCAC-UTSM-12
65
Part 4 Installation
1. Note ................................................................................ 65
2. Installation of Indoor Units ........................................... 66
3. Installation of Outdoor Units ........................................ 71
4. Heat Insulation of the Pipe ............................................ 81
5. Installation of Connective Pipe ..................................... 82
6. Installation of Drain Pipe ............................................... 87
7. Electric Connection ....................................................... 88
8. Methods of configuring and selecting installation ...... 90
1. Note
CAUTION:
Install the unit where enough space of installation and maintenance is available.
Install the unit where the ceiling is horizontal and enough for bearing the weight of the indoor unit.
Install the unit where the air inlet and outlet are not baffled and are the least affected by external air.
Install the unit where the supply air flow can be sent to all parts in the room.
Install the unit where it is easy to lead out the connective pipe and the drain pipe.
Install the unit where no heat is emitted from a heat source directly.
Installing the equipment in any of the following places may lead to faults of the equipment (if that is
inevitable, consult the supplier):
The site contains mineral oils such as cutting lubricant.
Seaside where the air contains much salt.
Hot ring area where corrosive gases exist, e.g., sulfide gas.
Factories where the supply voltage fluctuates seriously.
Inside a car or cabin.
Place like kitchen where oil permeates.
Place where strong electromagnetic waves exist.
Place where flammable gases or materials exist.
Place where acid or alkali gases evaporate.
Other special environments.
Install the unit where enough space of installation and maintenance is available.
Install the unit where the air inlet and air outlet are free from obstacles and strong wind.
Install the unit in a dry and well ventilated place.
Install the unit where the bearing surface is level and can bear weight of the unit, and is suitable for
installing the unit horizontally without increasing noise or vibration.
Install the unit where the operation noise and the expelling of air do not affect neighbors.
Install the unit where no flammable gas is leaked.
Install the unit where it is convenient for pipe connection and electric connection.
Содержание MDFA-76CRN2
