Midea LSBLG1120/MCFN Скачать руководство пользователя страница 51

Страница: 51 / 97

Flooded type water cooled screw chiller (PCB Control)

MCAC-CTSM-2012-11

(6) Inspect whether the flow in the water pump meets the requirements of the unit.

(7) Inspect whether the power supply of the unit is stable.

2) Parameters Inspections during Start-up and Operation

(1) The maximum range of parameters for normal operation of R134a refrigerant unit

See table 2 for the maximum range of performance parameters of R134a refrigerant:

[Table 2]

(1) Keep good record of unit data during commissioning.

2. Maintenance and Service

ATTENTION:

1) All installation parts must be maintained by the personnel in charge, in order to avoid material

deterioration and injuries to people. Faults and leaks must be repaired immediately. The

authorized technician must have the responsibility to repair the fault immediately. Each time

repairs have been carried out to the unit, the operation of the safety devices must be re-checked.

2) Do not use oxygen to purge lines or to pressurize a machine for any purpose. Oxygen gas reacts

violently with oil, grease, and other common substances.

3) The necessary protection equipment must be available, and appropriate fire extinguishers for the

system and the refrigerant type used must be within easy reach.

4) Do not siphon refrigerant. Avoid spilling liquid refrigerant on skin or splashing it into the eyes. Use

safety goggles. Wash any spills from the skin with soap and water. If liquid refrigerant enters the

eyes, immediately and abundantly flush the eyes with water and consult a doctor.

5) Never let an open flame or live steam close to a refrigerant container. Dangerous overpressure

can result. If it is necessary to heat refrigerant, only use warm water.

6) Do not re-use disposable (non-returnable) cylinders or attempt to refill them. It is dangerous and

illegal. When cylinders are empty, evacuate the remaining gas pressure, and move the cylinders

to a place designated for their recovery. Do not incinerate.

7) Ensure that you are using the correct refrigerant type before recharging the unit.Charging any

refrigerant other than the original charge type (R-134a) will impair machine operation and can

even lead to a destruction of the compressors. The compressors operating with this refrigerant

type are lubricated with a synthetic

Working Condition

Refrigeration

Discharge temp.

℃

40~50

℃

Suction temp.

℃

5~9

℃

Suction super-heating degree

℃

1~3

℃

Discharge super-heating degree

℃

10~15

℃

Discharge pressure MPa

0.8~0.9MPa

Suction pressure MPa

0.2~0.25MPa

Содержание LSBLG1120/MCFN


































































































Результаты поиска

Содержание LSBLG1120/MCFN

Отзывы:

Бренды по названию

Популярные бренды

Midea LSBLG1120/MCFN, Техническое и сервисное руководство

Результаты поиска

Содержание LSBLG1120/MCFN

Отзывы:

Бренды по названию

Популярные бренды