Midea LSBLG1120/MCFN Скачать руководство пользователя страница 46

Страница: 46 / 97

Flooded type water cooled screw chiller (PCB Control)

MCAC-CTSM-2012-11

[Communication Lines of PCB and Touch Screen]

1.2 Electrical Elements Parameters Settings Inspection

1) Inspect whether the compressor overload protection value, which shall not exceed the

maximum compressor permissible current value indicated in the nameplate on the compressor,

is set correctly. The compressor overload protection value generally equals to the set value of

heat relay multiplied by variable ratio of current inductor, which is (250/5)50 in the following

case.

2) Inspect whether the value of phase loss and reversal protection is set correctly. The

over-/under-voltage protection value shall be ±10% of the rated voltage.

1.3 Unit Parts and Inspection of Leak Points

1) The discharge line valve and suction line valve of the compressor must be fully open (turn

anticlockwise to open) and the cores shall be tightly locked to prevent leakage of refrigerant.

Protection setting of
compressor heat
relay overload value

The discharge line
valve and suction line
valve shall be open
(both valves in the
figure are closed, and
shall be opened
before start-up).

The discharge line
valve and suction line
valve shall be open
(both valves in the
figure are closed, and
shall be opened before
start-up).

Содержание LSBLG1120/MCFN


































































































Результаты поиска

Содержание LSBLG1120/MCFN

Отзывы:

Бренды по названию

Популярные бренды

Midea LSBLG1120/MCFN, Техническое и сервисное руководство

Результаты поиска

Содержание LSBLG1120/MCFN

Отзывы:

Бренды по названию

Популярные бренды