background image

2

To prevent personal injury, injury to others and property damage, the instructions below must be 

followed. Incorrect operation due to failure to follow instructions will cause harm or damage.

Special Caution

1. CAUTION

This water heater is for household use only and it can be installed indoors where

hot water is needed.

A plug is not used for this water heater; this water heater must be connected directly to a

circuit breaker with current leakage protection.
Please distinguish live line (red/brown),neutral line (blue) and earth line (green/yellow) 

during installation.
Do check whether the ampere rating of the household wiring is sufficient before installation,

and a dedicated circuit must be used when installing.
Before installing this water heater, check and confirm if the earth electrode in the socket is

reliably earthed and has no current flowing. If there is no ground electrode or incorrect ground

connection is done, the water heater will not work.
The hot water from the water heatermay cause scalding; please test and check the

temperature of the hot water before use.
The distance between water heater installed and water output should be as near as

possible to avoid loss of heat.
The electic water heater maybe damaged if the water hardness is too high. To ensure

longer product lifespan, please install nd put it into use where the local water hardness

is less than 450mg/L9CaCO3).

In times of lightning/thunder, switch “Off” the circuit breaker ahead of time, to protect

the water heater against possible damage.
Inspect the built-in ELCB (once a month)to avoid hazards to users such as damage to

property serious injury or death.

Do not cut off power supply before maintenance. Any maintenance or adjustment of

product by a non-professional is highly prohibited.
The damaged power cord must be replaced by  good one provided by the manufacturer,

and the replacement should be done by qualified technician or engineer or professionals of

similar products.

In order to avoid hazard due to inadvertent resetting of the Earth Leakage Circuit

Breaker (ELCB), this appliance must not supplied through an external switching device, such

as timer or connected to a circuit that is regularly switched “On” and “Off” by the utility.
This water heater is equipped with adjustable flow capacity safety valve. For safety use,

please do not change its installation location and do not block its water outlet.

For any improper installation and incorrect operation of this product, our company will not be

liable for any responsibility.
This water heater can be used for other purpose, e.g., washing hands, dishes or food,

and so on. (Multi-directional water supply is not available).
When the shower is used by children, elderly, sick or physically- handicapped persons, they

are requested to be attentive to and check the water temperature by hand, from time to time.

This shower head must be descaled regularly.

WARNING

The water heater should be earthed before use. Please ensure that the resistance of 

household earth wire is <4Ω. Otherwise you may receive an electric shock. Using the water heater

without earthing is highly prohibited.

!

Содержание ECOHEAT FP-67WTR380WMTH-B1














Отзывы: