Middle Atlantic C3-XX-LDXU Скачать руководство пользователя страница 6

Страница: 6 / 14

Page 6

INTRODUCTION

NOTE

• Only use this instruction sheet to install your C3 Series Display Mount option after you refer to the

C3 Series Credenza Frame instruction sheet (100-00032) and secure your frame to the wall using the

default (frame feet) installation height.

• Do not use the display mount option (C3-XX-LDXU) if your installation requires the credenza mounted

at a specific height and you cannot use the default (frame feet) installation height.

• If your installation includes a purchased fan kit and/or a large cover option (for your display option), after

installing this and the other options you may have purchased for your credenza, refer to the C3

Series WoodKit instruction sheet (100-00040) to install your woodkit, and then refer to the C3 Series

Fan Kit (C3-FANKIT) instruction sheet (100-00039) and/or C3 Series Display Mount Large Cover

Option instruction sheet (100-00035) to install your fan kit and/or your large cover option, respectively.

Kits and options other than the fan kit and large cover option should be installed before your woodkit

is attached to the frame

• Attaching display(s) (display(s) not included) to the horizontal extrusion must be done as the final

part of your C3 installation process. For more information, see "Attaching Display(s) to the Horizontal

Extrusion" on page 11.

• Instruction sheets may also be accessed at www.middleatlantic.com.

REQUIRED TOOLS

• Protective Eyewear

• Level

• #2 Phillips

Screwdriver

• Power Driver

• ⅜” Socket

• #2 Phillips Bit

• ½” Wrench

WARNING

: Use tools with caution and follow all

necessary safety protocols.

AVERTISSEMENT

: Utiliser des outils avec prudence

et suivre tous les protocoles de sécurité nécessaires.

SETTING MACRO DISPLAY HEIGHT ON YOUR UPRIGHT PAIR

NOTE

• Each upright includes the following pieces: pre-assembled lower portions comprised of inner posts

and outer sleeves, and horizontal mounts at the tops as shown. (

FIGURE A

)

Upright Pair Pre-assembled Lower Portions

Upright Pair Horizontal Mounts

FIGURE A

Inner Posts

Outer Sleeves

Содержание C3-XX-LDXU















Результаты поиска

Содержание C3-XX-LDXU

Отзывы:

Похожие инструкции для C3-XX-LDXU

Бренды по названию

Популярные бренды

Middle Atlantic C3-XX-LDXU, Инструкция

Результаты поиска

Содержание C3-XX-LDXU

Отзывы:

Похожие инструкции для C3-XX-LDXU

Бренды по названию

Популярные бренды