background image

AquaPrep 055 

Unpacking and Inspecting the Equipment

Oct 09                                                

2-1 

2.  INSTALLATION

This chapter describes how to unpack, inspect, and install the AquaPrep.

Unpacking and Inspecting the Equipment

The AquaPrep and its accessories should be visually inspected as soon as unpacked to ensure 
that all items have been received and none has sustained physical damage.

When you unpack the shipping cartons, carefully compare the packing list with the equipment 
actually received, while checking for equipment damaged during shipment. Be sure to sift 
through all packing materials before declaring equipment missing.

Equipment Damage or Loss During Shipment

When equipment is damaged or lost in transit, you are required to make note of the damage or 
loss on the freight bill. The carrier, not the shipper, is responsible for all damage or loss. In the 
event of equipment damage or loss during shipment, contact the carrier of the equipment 
immediately.

Equipment Return

Micromeritics strives to ensure that all items arrive safely and in working order. Occasionally, 
due to circumstances beyond our control, equipment is received which is not in working con-
dition. When it is necessary to return equipment (damaged either during shipment or while in 
use) to Micromeritics for repair or replacement, the following procedure should be followed:

1. Pack the instrument in its original shipping carton if possible. If the original carton is 

unavailable, for a nominal fee Micromeritics can provide another carton for your use.

2. Tag or identify the defective equipment, noting the defect and circumstances, if any, under 

which the defect is observed.

3. Reference the sales order or purchase order, and provide the date that the equipment was 

received.

It is important to save the shipping cartons when equipment is to be declared as 
damaged or lost. The inspector (or claim investigator) must examine the cartons prior 
to completion of the inspection report.

Failure to package your instrument properly may result in shipping damage.

Содержание AquaPrep 055























Отзывы: