Microhard Systems Pico P2400 series Скачать руководство пользователя | Manualshive

Страница: 70 / 87

background image

© Microhard Systems Inc.

Confidential

70

4.0 Register/Command Reference

Values

S163 CRC Check on Diag Port

0 - Disable

1 - Enable

Enables CRC checking of received data on local diagnostic port
Default - 1 (enable), 0 - disable. Note that even if disabled,
the incoming data must have two dummy bytes transmitted in place of
CRC bytes. See the P2400 Diagnostic Channel Protocol Manual for
more information.

Values

S167 Tx Enable

0 - Disable

1 - Enable

Tx Enable 0 - Disabled, 1- Enabled (default)
Enables RF emission.

Modem will never transmit data if disabled, it will be in a listen only
mode.

Values (0 - 254)

5

S213 Packet Retry Limit

Packet Retry Limit(0 - 254). Valid only for repeater's uplink (from child
to parent)

Values (0 - 254)

0

S214 Diagnostics Packet Retransmission

Enables the retransmission of Diagnostic Packets. Diagnostics Packet
Retransmission(0 - 254). 0 - (default)

See the P2400 Diagnostics Manual for more information.

Values

S217 Protocol Type

0

transparent

1

MODBUS RTU

2

DF1 protocol, full-
duplex, with address
filtering

For most applications, the default value of 0  - resulting in transparent
operation  -  will be maintained in this register. Setting this register to a
value  of  1  specifies  MODBUS  operation,  in  which  the  modem  will
frame  the  output  data  and  comply  with  MODBUS  specifications.
S217=2  configures  the  modem  for  DF1  filtering.    In  this  mode,  the
PLC’s address must match the Unit Address of the modem.  Data not
intended  for  a  specific  PLC/Modem  pairing  will  be  blocked  from
passing through the modem to the attached PLC.

Values

S238 Hopping Mode

0 - Hopping on pattern
1 - Hopping on frequency table
2 - Hopping on channel
3 - Hopping on frequency

Hopping mode register (S238) is preset by manufacturer. It is a read-
only register for the end user. S238 controls the modem either hopping
on pattern or on frequency table.

«
...
68
69
70
71
72
...
»

Содержание Pico P2400 series
























































































Отзывы:

Нет отзывов

Похожие инструкции для Pico P2400 series

3C892 - OfficeConnect ISDN Lan Modem Router

Бренд: 3Com Страницы: 8

Бренд: NAL Страницы: 180

Бренд: NAL Страницы: 107

PCTV HYBRID PRO STICK

Бренд: Pinnacle Страницы: 2

Бренд: TP-Link Страницы: 4

Бренд: Honeywell Страницы: 87

Бренд: Huawei Страницы: 9

Бренд: Panasonic Страницы: 6

Бренд: Panasonic Страницы: 58

Digital Business System

Бренд: Panasonic Страницы: 87

Бренд: Panasonic Страницы: 135

DIVA T/A ISDN Modem

Бренд: Eicon Networks Страницы: 146

Бренд: Hercules Страницы: 6

Бренд: B+B SmartWorx Страницы: 2

Бренд: nawras Страницы: 10

EZ Connect SMC7003-USB

Бренд: SMC Networks Страницы: 2

EZ Connect SMC2642W

Бренд: SMC Networks Страницы: 56

Бренд: NAL RESEARCH CORPORATION Страницы: 114

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды