8
2.2 Operating determinations
This device is a moving-head spot for creating decorative effects. This product is only allowed to
be operated with an alternating current of 230 V, 50 Hz and was designed for indoor use only.
This device is designed for professional use, e.g. on stages, in discotheques, theatres etc.
Lighting effects are not designed for permanent operation. Consistent operation breaks will ensure
that the device will serve you for a long time without defects.
Never run the device without lamp!
Do not shake the device. Avoid brute force when installing or operating the device.
Never lift the fixture by holding it at the projector-head, as the mechanics may be damaged.
Always hold the fixture at the transport handles.
When choosing the installation-spot, please make sure that the device is not exposed to extreme
heat, moisture or dust. There should not be any cables lying around. You endanger your own and
the safety of others!
The minimum distance between light-output and the illuminated surface must be more than 1 m.
Make sure that the area below the installation place is blocked when rigging, unrigging or servic-
ing the fixture.
Always fix the fixture with an appropriate safety-rope. Fix the safety-rope at the correct holes only.
Only operate the fixture after having checked that the housing is firmly closed and all screws are
tightly fastened.
The lamp must never be ignited if the objective-lens or any housing-cover is open, as discharge
lamps may explode and emit a high ultraviolet radiation, which may cause burns.
The maximum ambient temperature t
a
must never be exceeded.
CAUTION!
The lens has to be replaced when it is obviously damaged, so that
its function is impaired, e.g. due to cracks or deep scratches!
Operate the device only after having familiarized with its functions. Do not permit operation by per-
sons not qualified for operating the device. Most damages are the result of unprofessional opera-
tion!
CAUTION!
The lamp has to be replaced when it is damaged
or deformed due to the heat!
Please use the original packaging if the device is to be transported.
Please consider that unauthorized modifications on the device are forbidden due to safety rea-
sons!
Never remove the serial barcode from the device as this would make the guarantee void.
If this device will be operated in any way different to the one described in this manual, the product
may suffer damages and the guarantee becomes void. Furthermore, any other operation may
lead to dangers like short-circuit, burns, electric shock, lamp explosion, crash etc.
21
ENGLISH
- Lamp On automatically
This menu allows you to turn the lamp on after switching the fixture on
and switch on/off the lamp light sensor.
-
Lamp On after switching the fixture on
This function enables
to switch on the lamp automatically after switching on the fixture. Use
the [Up] and [Down] keys to select
„On”
if you wish to switch on the
lamp automatically after switching on the fixture or
„ Off”
if you wish the
lamp off after switching on the fixture and press
[Enter]
to confirm or
[Mode]
to cancel and return to the menu.
- Switch On/Off the lamp light sensor
Use the
[Up]
and
[Down]
keys to select
"On"
if you wish to switch the lamp light sensor On and press
[Enter]
to
confirm or
[Mode]
to cancel and return to the menu. The option "On" is for the s tandard operation.
Use the
[Up]
and
[Down]
keys to select
"Off"
if you wish to switch the lamp light sensor Off and press
[Enter]
to
confirm or
[Mode]
to cancel and return to the menu.
Important: The option"Off" is for "emergency operation" only if the lamp light sensor is defective and
you will wait for a delivery of the spare light sensor!
If the lamp light sensor was switched Off, the error mes-
sages
"LAEr,SnEr,HEAt"
will not appear on the display (only the message
"HEAt"
will appear if the lamp was
turned Off and On within 5 minutes ) and at switching On of the lamp the electronics will still try to ignite the lamp
until it shines (even when the lamp is damaged or absent), on this account some electronics parts could be dam-
aged!
- DMX values
Readout DMX values of each channel received by the fixture. Use the
[Up]
and
[Down]
keys to select desired
channel and press
[Enter]
to read its value coming to the fixture or
[Mode]
to cancel and return to the menu.
- Display-adjusting
This function allows you to adjust the display settings:
- Display intensity
With this function, you can adjust the display -intensity from 20 % to
100 %. Use the
[Up]
and
[Down]
keys to select the level of the dis-
play-intensity and press
[Enter]
to confirm or
Mode]
to cancel and
return to the menu.
- Display-reverse
With this function, you can rotate the display by 180°. Use the
[Up]
and
[Down]
keys to select
"normal display"
or
"display turned by 180°"
and press
[Enter]
to confirm or
[Mode]
to cancel and return to the menu.
- Display-On
This function allows you to keep the display on or to turn off automatically 2 minutes after last pressing any key
on the control board. Use the
[Up]
and
[Down]
keys to select
"On"
if you wish to keep the display on or
"Off"
if
you wish to turn off automatically 2 minutes after last pressing any key on the Control Board and press
[Enter]
to
confirm or
[Mode]
to cancel and return to the menu.
- PAN/TILT-Feedback:
This function allows to return the
ULTRA SPOT
to the required position after changing the position by external
force (e. g. by stroke). Use the [Up] and [Down] keys to select "On" if you wish to enable this function or "Off" if
you wish not to return the Moving Head to the required position and press [Enter] to confirm or [Mode] to cancel
and return to the menu.
Note:
If feedback was switched Off, the PAN/TILT-position is changed by external force and feedback is
switched On again, the Moving Head might not to be synchronized with the DMX signal. You have to make a
reset in order to synchronize the
MICROH ARENA ULTRA SPOT
with the DMX signal.
