18
This situation can occur if:
the 3 PIN XLR plug (cable with DMX signal from controller) is not connected with the input of the
ULTRA SPOT
the controller is switched off or defective, if the cable or connector is defective or
the signal wires are swap in the input connector.
Note:
It’s necessary to insert the XLR termination plug (with 120 Ohm) in the last lighting in the link in
order to ensure proper transmission on the DMX data link.
6. REMOTELY CONTROLLABLE FUNCTIONS
6.1 Lamp
The
ARENA ULTRA SPOT
is to be operated with a PHILIPS MSR 575/2 MSD 575 lamp.
A relay inside of the
ARENA ULTRA SPOT
allows you to switch on and off the lamp via the Con-
trol Board on the top side or via your controller without affecting the rest of the lighting.
6.2 Switching on and off the lamp via the Control Board
1.
Switch on the
ARENA ULTRA SPOT
and wait until the fixture reset has finished.
2.
Press the
[Mode]
key in order to access the main menu. Browse through the menu by pressing
the [Up] and [Down] keys until the display shows
"LAM P
". Confirm by pressing
[Enter]
key.
3.
Use the [Up] and [Down] keys to select
"On"
for switching on the lamp and
"Off"
for switch off
the lamp and press
[Enter]
to confirm or
[Mode]
to cancel
.
Note :
It is also important to note that the discharge lamp is a cold restrike type, which means that it has to be cold
before re-striking. For this reason, you have to wait 5 minutes (max. speed of fan must be adjusted) after hav-
ing switched off the lamp before you can switch it back on again. If you try to switch on the lamp within 5 min-
utes after having switched it off, the
ULTRA SPOT
will store this information and automatically ignite the lamp
when the 5 minutes period has expired. The message
"HEAt"
will appear on the control board display at the
back side of the
ULTRA SPOT
. If the ignition of the lamp is seven times unsuccessful, on the display will ap-
pear
"LA.Er
", meaning that the lamp could be damaged or even missed, or there could be a failure on the igni-
tor or ballast.
6.3 Colour wheels
The
ULTRA SPOT
has two colours wheels both with 10 color positions - 9 of these with dichroic
colors and the last one open. Colour wheel 1 can be positioned between two adjacent colors in any
position. It is also possible to rotate colour wheel 1 continuously at different speeds (“Rainbow ef-
fect“) in both directions. Hot and cold colour temperature filters (3200 K and 6000 K) and the UV-
filter are situated on colour wheel 2. By color macro function it is possible to obtain 64 different col-
ours in following order: white, pink, magenta, red, orange, yellow, green, cyan, blue, UV
6.4 Static gobo wheel
This wheel has 9 metal gobos + open position, all gobos are interchangeable. The gobos have an
outside diameter of 27 mm and an image diameter of 23 mm. Gobo wheel rotation from slow to
fast can be also adjusted. Furthermore, it has the gobo-shake function.
6.5 Rotating gobo-wheel
The rotating gobo-wheel includes 3 metal gobos, 1 glass gobo and 2 multicolor dichroic gobos ro-
tating in both directions, indexable, rotating gobo wheel cont. rotation slow to fast. All gobos are
interchangeable. The gobos have an outside diameter of 27 mm and an image diameter of 23 mm.
11
ENGLISH
3.3 Rigging
The installation of the projector has to be built and constructed in a way that it can hold 10
times the weight for 1 hour without any deformation.
The installation must always be secured with a secondary safety attachment, e.g. an appro-
priate safety cable.
This secondary safety attachment must be constructed in a way that no part of the fixture can
fall in the event of a primary failure.
When rigging, unrigging or servicing the fixture staying in the area below the installation, on
bridges, under high working places and other endangered areas is forbidden.
The operator has to make sure that safety related and machine technical installations are a p-
proved by an expert before operating the fixture for the first time or after changes have been
made to the installation.
Procedure:
The projector should be installed outside areas where persons may walk by or be seated.
IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE
, including
(but not limited to) calculating working load limits, installation material being used, and peri-
odic safety inspection of all installation material and the projector. If you lack these qualifica-
tions, do not attempt the installation yourself, but instead use a professional structural rigger.
Improper installation can result in bodily injury and/or damage to property.
The projector has to be installed out of the reach of people.
If the projector shall be lowered from the ceiling or high joists, professional trussing systems
have to be used.
The projector must never be fixed swinging freely in the room.
Caution:
Projectors may cause severe injuries when crashing down! If you have doubts
concerning the safety of a possible installation, do NOT install the projector!
DANGER OF FIRE!
When installing the device, make sure there is no highly-inflammable
material (decoration articles, etc.) within a distance of min. 0.5 m.
CAUTION!
Use 2 appropriate clamps to rig the fixture on the truss.
Follow the instructions mentioned at the bottom of the base.
Make sure that the device is fixed properly! Ensure that the structure
(truss) to which you are attaching the fixtures is secure.
