Microchip Technology PIC12F1501 Скачать руководство пользователя страница 145 | Manualshive

Страница: 145 / 402

Microchip Technology PIC12F1501 Скачать руководство пользователя страница 145

PIC16(L)F1508/9

DS40001609E-page 146



2011-2015 Microchip Technology Inc.

FIGURE 17-2:

SINGLE COMPARATOR

17.2

Comparator Control

Each comparator has two control registers: CMxCON0
and CMxCON1.
The CMxCON0 registers (see

) contain

Control and Status bits for the following:
• Enable
• Output selection
• Output polarity
• Speed/Power selection
• Hysteresis enable
• Output synchronization
The CMxCON1 registers (see

) contain

Control bits for the following:
• Interrupt enable
• Interrupt edge polarity
• Positive input channel selection
• Negative input channel selection

17.2.1

COMPARATOR ENABLE

Setting the CxON bit of the CMxCON0 register enables
the comparator for operation. Clearing the CxON bit
disables the comparator resulting in minimum current
consumption.

17.2.2

COMPARATOR POSITIVE INPUT
SELECTION

Configuring the CxPCH<1:0> bits of the CMxCON1
register directs an internal voltage reference or an
analog pin to the non-inverting input of the comparator:

• CxIN+ analog pin
• DAC1_output
• FVR_buffer2
• V

SS

See

Section 13.0 “Fixed Voltage Reference (FVR)”

for more information on the Fixed Voltage Reference
module.
See

Section 16.0 “5-Bit Digital-to-Analog Converter

(DAC) Module”

for more information on the DAC input

signal.
Any time the comparator is disabled (CxON =

0

), all

comparator inputs are disabled.

17.2.3

COMPARATOR NEGATIVE INPUT
SELECTION

The CxNCH<2:0> bits of the CMxCON0 register direct
one of the input sources to the comparator inverting
input.

17.2.4

COMPARATOR OUTPUT
SELECTION

The output of the comparator can be monitored by
reading either the CxOUT bit of the CMxCON0 register
or the MCxOUT bit of the CMOUT register. In order to
make the output available for an external connection,
the following conditions must be true:
• CxOE bit of the CMxCON0 register must be set
• Corresponding TRIS bit must be cleared
• CxON bit of the CMxCON0 register must be set
The synchronous comparator output signal
(CxOUT_sync) is available to the following peripheral(s):
• Configurable Logic Cell (CLC)
• Analog-to-Digital Converter (ADC)
• Timer1
The asynchronous comparator output signal
(CxOUT_async) is available to the following peripheral(s):
• Complementary Waveform Generator (CWG)

–

+

V

IN

+

V

IN

-

Output

Output

V

IN

+

V

IN

-

Note:

The black areas of the output of the
comparator represents the uncertainty
due to input offsets and response time.

Note:

To use CxIN+ and CxINx- pins as analog
input, the appropriate bits must be set in
the ANSEL register and the correspond-
ing TRIS bits must also be set to disable
the output drivers.

Note 1:

The CxOE bit of the CMxCON0 register
overrides the PORT data latch. Setting
the CxON bit of the CMxCON0 register
has no impact on the port override.

2:

The internal output of the comparator is
latched with each instruction cycle.
Unless otherwise specified, external
outputs are not latched.

«
...
143
144
145
146
147
...
»

Содержание PIC12F1501



















































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды