manualshive.com logo in svg

MicroBoards Technology Orbit II, Справочное руководство

Поделиться
Скачать
MicroBoards Technology Orbit II Скачать руководство пользователя страница 39

                                                                           Orbit II Disc Copier Reference Manual – Revision K

 

39

 

 

Attachment B: Orbit II Error Messages 

 
 

Error Message: 

 Problem 

Description: 

        

 
!! Bad Copy!!

 

The copy CD is bad and will be rejected.  This message may briefly appear 
during any of Orbit II’s operating modes. 

 

!!ERROR!! No CD Reader!

 

This message would appear during a power on self-test if the copy controller did 
not locate a compatible CD Reader.  Contact Microboards Technology Technical 
Support. 

 
!!ERROR!! No CD-R Drives!

  This message would appear during a power on self-test if the copy controller did 

not locate a compatible CD-R/CD-RW Writer.  Contact Microboards Technology 
Technical Support. 

 
!!ERROR!! Disc is Blank!

 

This message would appear at the start of a copy or compare job if the copy 
controller could not read the disc that is in the CD Reader.  Check your master 
CD, CD-R, or CD-RW discs, and try again.  If this message persists, contact 
Microboards Technology Technical Support. 

 
Setup Error

 

The user Setup file has been corrupted.  Turn the external power supply OFF, 
and leave it OFF for a few moments.  When you turn your Orbit II System back 
ON it will reset the user Setup file to the factory default values of 

Burn CD? Yes

 

and 

52x Write? Yes

.  If you are not using these default settings, make the 

appropriate 

System

 

Setup? 

changes before you use your Orbit II System. 

 

!!WARNING!! Copier

 

Your Orbit II System Setup has been changed to 

Burn CD? No.

  If you want to  

is in SIMULATE mode

  

proceed with the operation you selected press the 

Yes 

key.

  

If you do not want  

 

to proceed in simulate mode, press the 

No

 key and change the 

System Setup?.

  

 

Master Drive Error

 

The Reader drive could not successfully read from the master.  If you have been 
able to successfully duplicate the master previously, use a copy as the master for 
duplication purposes.  If duplication is successful from the copy, the master may 
contain burn errors from the original mastering or may be physically damaged; 
continue using the copy as the master.  If the copy returns the same error, 
contact Microboards Technology Technical Support. 

 

 

         

Содержание Orbit II








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды