micro-trak FLOWTRAK II Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 44

micro-trak FLOWTRAK II Скачать руководство пользователя страница 29

After the “-” (RESET) button has been held for 3 seconds,

the “CLEAr” message will be replaced by 0.0, indicating that

counter pair #3 has been cleared.

When the desired counter number is displayed, press the

“-” (RESET) button and “CLEAr” will be displayed.

NOTE: holding the “-” (RESET) button for 2 seconds will

clear both the #3 AREA counter and the #3 VOLUME

counter whether the rotary switch is in the AREA or the

VOLUME position.

If the “-” button is released before 2 seconds have elapsed,

the counters will not be cleared and the “CLEAr” message

will be replaced with the previous total.

WIDTH

CAL

FLOW

CAL

MIN

FLOW

TARGET

RATE

SPEED

CAL

TEST

SPEED

VOLUME /

MINUTE

DISTANCE

AREA /

HOUR

VOLUME

(1) (2) (3)

RATE

SPEED

AREA

(1) (2) (3)

TANK

CAL

RESET

MAN

HOLD

CALHOLD

3

II

TANK

VOL

TANK

ALARM

RUN

HOLD

HOLD

3

Resetting System Counters

To Clear Counters

29

«
...
27
28
29
30
31
...
»

Содержание FLOWTRAK II













































Отзывы:

Нет отзывов