micro-trak FLOWTRAK II Скачать руководство пользователя страница 19

Страница: 19 / 44

WIDTH CAL:

Enter the effec tive working width of the

entire boom, in inch-

es (meters). Your

“working” width per

boom section will be

the number of nozzles on the boom section

times the nozzle spacing in inches (mm). For

example, if you have 7 nozzles spaced at 20

inches, the working width of the boom section

is 140 inches.

WIDTH

CAL

AREA

(1) (2) (3)

TARGET RATE:

Enter the value for the desired target

application rate in gallons per acre (liters per

hectare) or lbs. of N per acre (kgs of N per

hectare). During operation, the warning light

will flash if the actual application rate is +/-

10% from the calibrated target rate.

TARGET

RATE

TANK ALARM SET POINT:

Enter the tank alarm set

point in gallons (liters) or lbs. (kgs) NH3. Use the “+” and

“-” buttons to set the level where the Warning LED starts

flashing and the word “FILL” flashes on the

display. Range is OFF or 1-65,535. When the

tank value drops below

the set point, the alarms

will notify the user that

the tank level is low.

Note: this feature is inoperative if the system is set up in the

(Tank) FILL mode.

See Special Calibration (pages 25-26) and

Tank fill Operation (page 30) for setup and operation details

for the Tank FILL mode.

TANK

ALARM

AREA /

HOUR

TANK VOL:

If using the Tank feature, this setting can be

used to enter the volume of the tank in gallons (liters, lbs.

NH3). Use the “+” and “-” buttons to choose OFF or any value

from 1-65,535. Then when the tank is filled,

the tank counter can be reset to full by simply

turning the rotary switch to the TANK position

and pressing the “+”

button. Depending on

the “UNITS” setting, the

TANK SIZE units will be

either gallons or liters. If “material” is set to NH3, the Tank

Size will be in lbs. or kg. Anhydrous Ammonia (NH3).

Note:

the TANK VOLUME remaining feature does not work if the

system is programmed in the (Tank) FILL mode.

See page

30 for setup and operation details for the Tank FILL mode.

TANK

VOL

TANK

SPEED CAL:

This position is used to calibrate the speed

sensor for ac cu rate

speed and dis tance

measurement. When

this position is selected,

the display will show THE SPEED CAL value.

SPEED

CAL

DISTANCE

Calibration

(cont)

Entering Calibration Values

Содержание FLOWTRAK II













































Результаты поиска

Содержание FLOWTRAK II

Отзывы:

micro-trak FLOWTRAK II, Справочное руководство, Страница: 19 / 44

Результаты поиска

Содержание FLOWTRAK II

Отзывы: