manualshive.com logo in svg

Micro Rain MR43, Инструкция по эксплуатации

Поделиться
Скачать
Micro Rain MR43 Скачать руководство пользователя страница 15

13

interization 

1.  Disconnect supply hose from machine to allow any waler In and    

     above inlet fittings to drain out.

2.  Drain plug on the bottom of the turbine must be drained to prevent  

     freeze damage to turbine housing and impeller.  Drain plug is lo-   

     cated on the bottom side of the turbine.

3.  It is important ti unrack the guncart on the MR40 & MR43, open    

     the shutoff valve, and allow water above lhe valve to drain out of the  

     sprinkler.  Shutoff valve on MR50 throughMR58RL located under  

     the red cover should be latched in the open position as well.  This  

     will allow any remaining water to expand out and not cause any    

     damage to the valve.

4.  Drain guncart body by taking out draln plug localed on the bottom  

     elbow of the cart on all large chassis Micro Rains - MR40 through  

     MR5BRL.

5.  Drain boost pump case by opening 1/4” ball valve as shown in left  

     photo.  On boost pump models, disconnect the short black con-  

     nection hose on the side of the Micro Rain that connects the    

     boost pump piping to the inlet side of the machine. This allows  

     water in the cross-pipe to drain; preventing damage to the pipe or  

     flow switch.

aintenance Schedule 

Fittings & Seals:  

Grease fittings and seals every 100 hours.

Wheel Hubs:

  Grease all wheel hubs every 100 hours.

Drum Gear:  

Grease the drum gear at least twice per season.

Gearbox:  

Change gearbox oil once a season with 80W/90 gear oil.

Level Wind:  

Check tire pressure every 4-6 weeks.

NOTE:

  Water left in poly hose may be blown out with an air compressor by coverting an Inlet fitting with an air chuck 

adaptor. These fittings are available through KID Group if needed.

Содержание MR43

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды