manualshive.com logo in svg

Micro Rain MR43, Инструкция по эксплуатации

Поделиться
Скачать
Micro Rain MR43 Скачать руководство пользователя страница 11

9

1.  Check the oil level of the gearbox and if necessary add SAE  

     80W/90. Keep oil level at the side plugs in the gearbox in  

     order to bathe the shift fork in oil.

2.  Grease the machine thoroughly (all grease fittings) and    

     thereafter, grease every 100 hours. Pay close attention 

     to the two grease fittings on the drum inlet. One grease 

     fitting is located on the bottom side and lubricates the 

     drum inlet seals. Grease must be spread on the drum 

     gear teeth and at the drive shaft where the drum gear 

     and drive gear mesh. The scroll bar must also be kept 

     well greased, and the scroll knife must be lubricated 

     (grease fitting) in order to function correctly.

3.  Check the tire pressure and if necessary, inflate to pressure  

     recommended on the tire (generally 35 PSI).

LUBRICANT TABLE

Gearbox

SAE 80W/90

Reel Supports

Grease NLGI No.2

Grease Fittings

Grease NLGI No.2

Содержание MR43

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды