Micro Rain MR43 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 24

Micro Rain MR43 Скачать руководство пользователя страница 12

10

The MR43 is designed for clean water suitable for irrigation. The machine is not designed for water

that includes large pieces of debris or slurry/wastewater conditions.

1. Tow the machine to the working site (off-road only).

WARNING!!

Maximum speed is 7 MPH. Before towing the

machine, be sure no one is standing behind or around the

machine; make sure the gun cart is racked.

2. Face the gun cart side of the reel towards the area needing to

be irrigated. The machine direction should be as straight

as possible. Set the stabilizer.

3. Lower the gun cart.

4. Connect the water supply hose to the water inlet connection

on the machine.

NOTE:

Before connecting the supply hose to the machine, flush

out hose or check to be sure there is no foreign matter which

will block the turbine.

5. Release the backstop (anti-reverse) lever. Pull straight back and

down to release.

6.

IMPORTANT!!

Make sure the gearbox lever is in the

disengaged or idle position before unwinding tube.

«
...
10
11
12
13
14
...
»

Содержание MR43

























Отзывы:

Нет отзывов