MHSC WDV500 Скачать руководство пользователя страница 36

36

78D0011

WDV Series Gas Fireplace

tOuch screen reMOte cOntrOl OperatIOn

setting privacy code on transmitter:

Figure 44

The remote transmitter privacy code is preset in factory.  
In the event of activation or interference from other nearby 
transmissions, change the code using the following pro-
cedures (learn function must be performed after changing 
the code):
1.  Press  the  ON/arrow  button  and 

the  TIMER  button  at  the  same 
time  to  enter  privacy  code  setup 
mode. 

2.  The setup display is shown in the 

figure. The four digits on the top 
stand for the privacy code (as the 
actual DIP switches on Ambient’s 
previous  remotes).  The  default 
values of the four digits will be all 
“1” (ON).

3.  The first digit will be flashing upon 

entering the setup mode. Push the ON button to toggle 
its value between “0” (OFF) and “1”(ON), and push the 
“OFF” button to jump to the next digit. The next digit 
will then start flashing and the first one stops flashing. 
Set up the four digits to your choice.

4.  After setting up all the four digits, push “OFF” to finish 

the process and return to the previous mode.

5.  The Signature Command control board then needs to 

re-learn the new setting.

performing learn Function

1.  The RF  receiver button on the control board in the fire-

place must be in the on position before the learn func-
tion can begin. 

Figure 45.

 With the Command Center 

master switch in the ON position, use paper clip to de-
press the recessed button on Control Board, one beep 
for RF receiver ON or two beeps for RF receiver OFF.

2.  Holding  the  OFF  button  on  the  Command  Center 

while turning on the 
master  switch  will 
activate  the  learn 
function  for  the 
transmitter.

3.  After the above op-

eration,  two  beeps 
will  be  given  and 
the  green  LED  on 
the Command Cen-
ter  will  flash  for  10 
seconds.

W

arn

In

G

Do not use two (2) or more remote control sys-
tems  in the same area with the same privacy 
code  setting,  as  they  will  communicate  with 
each other.  this may cause the appliances to 
malfunction.

FP2649
set privace code

Figure 44

FP2650
command ctr ctrl brd

RF Receiver 
ON/OFF

control Board

Figure 45

FP2650
command ctr ctrl brd

Battery Door

Master Switch

ON

LED

OFF

FP2650

command center

Figure 46

4.  During the 10 seconds, press the OFF button on the 

transmitter to learn. Another two beeps will be given to 
confirm a successful learning. 

Figure 46

resetting the transmitter:

If the transmitter is not working properly, reinstall the bat-
teries to reset the transmitter.
1.  Pull out at least one of the batteries.
2.  Press any key on the screen to discharge.
3.  Wait for 10 seconds and reinstall the batteries.
Pushing and holding any key for more than 10 seconds 
until the display refreshes will also reset the transmitter.

n

  Functions and Operations

General:

The TSFSC Remote Control has four (4) operating modes: 
Manual, Timer, Thermostatic and Smart Mode. The con-
trol system can be set to temperature range between 45° 
F and 90° F. The blower speed and flame height can be 
adjusted in the manual, timer and thermostatic mode. The 
Smart  Mode  will  automatically  adjust  flame  height  and 
blower  speed  according  to  the  difference  between  Set 
and Room temperatures.
The  transmitter  will  operate  the  remote  receiver  from  1 
foot  to  a  maximum  of  30  feet.  The  distance  is  reduced 
when batteries are low.

Manual Mode

Figure 47

In  this  mode,  the TIMER  button  and  the THERMO  but-
ton  will  only  display  “TIMER”  and  “THERMO”,  respec-
tively without showing the time and the SET temperature. 
Pressing  the  ON/up  and  OFF/down  buttons  will  change 
the  flame  height  if  none  of  the  menu  buttons  (TIMER, 
THERMO, LIGHT, FAN, AUX) are pressed and flashing.

Содержание WDV500





















































Отзывы: