MHSC WDV500 Скачать руководство пользователя страница 20

20

78D0011

WDV Series Gas Fireplace

1.  Flexible UL1777 listed venting may be used in any venting application where rigid direct vent components 

can be used. 

all restrictions, clearances and allowances that pertain to the rigid piping apply to 

the flexible venting.

 Flex kits may not be modified. Flex kits may be 

added to the end of a vent run made of rigid vent sections using pipe 
manufacturer's  approved  flex  to  pipe  adapters.  This  may  occur 
only if doing so does not violate any of the venting length, height, 
routing, horizontal to vertical ratio requirements or clearance 
considerations detailed in this manual.

2.  The flex adapter starter kit (DVFF8A/8) is used to attach 

flex venting to the appliance starting collar. It includes 5" 
inner and 8" outer adapter rings. 

Figure 27

  The inner and outer adapter rings are required to start 

all flex runs.

   Never install damaged or torn flexible venting.

   Over  tightening  clamps  may  rip,  tear,  or  otherwise 

damage flexible venting.

   The adapter kit does not include individual pipe sec-

tions which may be purchased separately. (UL1777 
listed type venting only.)

3.  Start the flexible vent as follows:

A.  Installing the inner flex adapter and pipe. 

Figure 27

1.  Insert  the  long  side  of  the  5"  inner  ring  into 

exhaust pipe, gently tap to seat into place, and secure with 
screws.

2.  Slide the small gear clamp over the inner flexible vent pipe, 

and push out of the way.

3.  Pull and extend the inner flexible vent.
4.  Slide the inner vent onto the adapter collar, for a minimum 

1

C\v

" overlap.

5.  Locate the clamp at approximately 3/4" from the flex end and tighten.
6.  Secure the clamped inner section with three self-tapping screws, drilled 

equidistant, just above the clamp perimeter.

B.  Installing the outer flex pipe. 

Figure 27

1.  Firmly insert the 8" outer adapter ring into the outer appliance starting collar 

and secure with screws.

2.  Slide the large gear clamp over the outer flexible vent pipe, and push out 

of the way.

3.  Pull and extend the outer flexible vent.
4.  Slide the outer vent onto the appliance collar outer adapter for a minimum 

1

C\v

" overlap.

5.  Locate the clamp at approximately 3/4" from the flex end and tighten.
6.  Secure the clamped outer section with three self-tapping screws, drilled 

equidistant, just above the clamp perimeter.

C. Routing UL1777 flex pipe.

1.  Always maintain the required clearance when routing the flex vent assembly.

Flex Vent InstallatIOn

n

O

te

F l e x   v e n t   p i p e   s p a c e r s :   r e f e r   t o 
manufacturer’s  specifications  for  correct 
positioning  of  the  spacer  springs  to 
maintain  proper  distance  between  inside 
and outside pipe.

FP1972
appliance connection

UL1777
Flex Vent

Screws 

(3 places, 

equidistant just 

above gear 

clamp)

1

C\v

" Flex-

ible Pipe 
and Adapter 
Outer

DVFF8A/8 
Inner Adapter 
Outer Adapter

Appliance 
Starting Collar

Figure 27 - 
Typical Appliance Connection

FP1973
flex pipe bend

UL1777
Flex Vent

5° Radius

Figure 28 - 
Minimum Radius for Flex 
Vent Section

FP1973

Содержание WDV500





















































Отзывы: