manualshive.com logo in svg

MHS Boilers REGENCY 2 G100/110IE, Руководство по установке, Страница: 18 / 24

Поделиться
Скачать
MHS Boilers REGENCY 2 G100/110IE Скачать руководство пользователя страница 18

18

REGENCY2

L O W

P R O F I L E

Ensure that the boiler is full of water and the system, boiler is fully vented.

Ensure that the pressure gauge on the boiler control panel reads a minimum of 0.5 bar (5m).

Ensure that an adequate gas supply is available at a working inlet pressure of 20mbar (Nat gas only) and
that the gas supply has been properly tested and purged in accordance with current Codes of Practice.

Ensure that the system pumps are running and water is circulating around the system.

fully automatic versions - G100/30-110IE

1. Switch on the on/off switch and ensure that the “green” power on indicator lamp illuminates.

2. Ensure that the external controls are calling for heat and that the “amber” “pump run” indicator lamp 

illuminates and that the boiler pump (if fitted) is rotating correctly.

3. The spark ignitor should start after a short delay the burner should ignite and the spark should stop.

4. Turn off the boiler at the on/off switch.

5. Attach a manometer to the burner pressure test point and turn on the boiler, ensuring gas pressure 

is not excessive.

6. Allow the main burner to operate for ten minutes and then check/adjust the burner pressure in 

accordance with the figure quoted in the technical data, and record combustion readings.

7. Turn off the appliance and remove the manometer. Ensure that the test point screw is firmly tightened.

8. Check correct operation of the control and limit thermostats, and lockout also the flue spillage limit 

thermostat on models G100/30-50IE.

9. Check connections for water tightness.

10. Check effective operation of the flue.

11. Instruct the user on the safe operation of the appliance and the need for regular maintenance.

Hand over operation instructions.

to turn off the boiler

1. FOR SHORT PERIODS

Switch off the on/off switch.  This will leave the pilot burner alight on permanent pilot models (towns 
gas only) and will obviate the need to carry out the lighting procedure when the boiler is required again.

To operate the appliance again, switch on the on/off switch.

2. FOR LONG PERIODS

Switch off the on/off switch. Turn off the gas supply at the gas isolation valve in the supply pipework 
to the boiler.

Switch off the power supply at the local isolator.

Drain boiler during periods of potential frost damage.

To operate the appliance again, follow appropriate comm/testing procedure.

4.0 commissioning

testing

Содержание REGENCY 2 G100/110IE

























Отзывы:

Нет отзывов