Mhouse MhouseKit WG2S, Инструкция по установке и эксплуатации

Страница: 41 / 132

English
English – 7
19. Test a number of manoeuvres moving the gate by hand. Check that
the fork slides smoothly on the worm gear of the gearmotor and that
there are margins of at least 5 mm on the opening and closing limits,
while avoiding a situation in which an excessive section of the worm
gear is not used;
20. If necessary, adjust the limit switch of the gearmotor, loosening it by
means of the hex wrench [G] and moving it to the required position
( fig. 19 ). The mechanical opening limiter [H] is only used if there are
no limit stops present. The mechanical opening limiter [I] is only used
if there are no limit stops present. After adjusting the limiters tighten
the screws fully down:
21.
Fix the front support permanently using screws suited to the leaf
material;
22. Unlock the gearmotor again using the release keys (see paragraph
11.3 - User’s Guide) .
Make electrical connections. Refer to figure 24 and step 6.
––– STEP 6 –––
6.1 - INSTALLING CL2S CONTROL UNIT
01. Select the installation position in an area protected against potential
impact and in the vicinity of the gate, to reduce the overall length of
the cables;
02.
Remove the cover, levering it off with a screwdriver from the opening
on the base; slide it by a few centimetres then lift it off the base ( fig.
21 );
03. Lay the duct for routing the electric cables so that they can be insert-
ed from the lower section of the control unit;
04. Drill the lower side of the control unit and use special connectors for
securing the ducts for routing electric cables, as shown in fig. 22 ;
05. On the base, use a screwdriver to punch through the two holes; trace
the drilling points using the base as a reference (
fig. 23
);
06.
Use a percussion drill to drill the wall, with a 6 mm tip, and insert 6
mm plugs.
07. Fix the base, using the relative screws [A] ;
08. Before closing the control unit, make the electrical connection with
reference to paragraph 6.6 and fig. 24 .
09. To close the control unit, place the cover on the base by approx. 3
cm higher than the final position and push it downwards to engage it
completely, as shown in
fig. 28
.
6.2 - INSTALLING AND CONNECTING PH100 PHOTO-
CELLS (fig. 29)
Warning: all installation operations must be performed with the system
disconnected from the power supply; if fitted, the PR1 backup battery
must also be disconnected.
Warnings:
Take care not to damage the o-ring fitted (
fig. 29-3
)
[A]
.
Select the position of the two elements making up the photocell (TX and
RX) observing the following:
• Place them at a height of 40-60 cm from the ground, to the sides of the
zone to be protected, and as close as possible to the edge of the gate,
i.e. no further than 15 cm.
• There must be a raceway tube at the point envisaged for routing cables.
• Point the transmitter TX at receiver RX with a maximum tolerance of 5°.
01. Remove the front glass panel ( fig. 29-1 ).
02. Position the photocell at the point where the cable routing tube
arrives.
03. Trace the drilling points using the base as a reference. Use a percus-
sion drill to drill the wall, with a 5 mm tip, and insert 5 mm plugs.
04. Route the electric cables through the specific holes (pierce those
required): see the two options in
fig. 29-2
.
05. Fix the base, using the relative screws [B] of fig. 29-3 ensuring that
the hole on the base [C] of fig. 29-3 is aligned with the cable outlet.
2 self-tapping screws are also supplied for fixture on surfaces with a
different density.
06. Connect the electrical cable in the relative terminals of both TX and
RX ( fig. 29-4 ).Connect the electrical cable in the relative terminals of
both TX and RX ( fig. 29-5 ) No polarity needs to be observed .
07. Fix the covering shell [D] of fig . 29-6 with the two screws [E] of fig.
29-6 using a Phillips screwdriver. Lastly, insert the external cover [F]
in
fig. 29-6
pressing it slightly to secure in place.
6.3 - INSTALLING AND CONNECTING THE FLASHING
LIGHT FL100 (fig. 30)
Select the position of the flashing light so that it is in the vicinity of the
gate in a visible location. It can be fixed on either a horizontal or vertical
surface. Fig. 30 shows the two options:
01. Remove the cover, unscrewing the screw if present.
02. Separate the base, unscrewing the screws present to route the elec -
tric cables.
03. Trace the drilling holes using the base as a reference and ensuring
that the hole on the base is aligned with the cable outlet: vertical fix -
ture ( A ) or horizontal fixture ( B ) .
04. Use a percussion drill to drill the wall, with a 6 mm tip, and insert 6
mm plugs.
05. Fix the base, using the relative screws.
06. Connect the electric cables in the relative FLASH and “aerial” termi -
nals as shown in the figure: To facilitate operations, remove termi -
nals, make connections, then refit the terminals.
No polarity needs to be observed on the FLASH terminal, while in the
case of the shielded cable connection of the aerial, the sheath must
be connected.
07. Insert the lamp holder in the base, taking care to press it down so
that it locks into place.
08. Secure the body of the flashing light to the fixing support and turn it
left until it clicks into place, then secure by means of the screw.
6.4 - ELECTRICAL CONNECTION TO CONTROL UNIT CL2S
To make the electrical connection, at very low voltage, of the various
devices, refer to fig. 24 .
01. To connect the gearmotors: remove the gearmotor cover as
shown in fig. 20 .
02.
Loosen the cable clamp located below the gearmotor, route through
the electric cable, then tighten the cable clamp fully down ( fig. 25 ).
03. Make the electrical connections observing the colour coding shown
in fig. 26 .
04. Close the cover of the gearmotor.
At this point, make the electrical connections of the various devic -
es (see the paragraphs of the various accessories).
• The terminals have the same colour as the terminals on the correspond -
ing devices; for example the grey terminal (OPEN) of the KS100 key-oper -
ated selector switch must be connected to the grey terminal (OPEN) of
the control unit;
• No polarity is needed for virtually any of the connections; only in the
case of the shielded cable of the aerial, the central core and sheath must
be connected as shown in detail [A] of fig. 24 .
Notes: - To facilitate connections, terminals can be removed as shown
in
fig. 27 - [A]
; after making the connections, refit the terminals in their
seats. - - At the end of connections, use cable ties to secure the electric
cables to the relative fixtures ( fig. 27 - [B] ) .