MG TR-EVO Скачать руководство пользователя страница 21

Warranty

M.G. industry srl

  guarantees its product, identified via a manufacturing code or by a brand 

name, is free of material and manufacturing defects which would mean it does not conform to the 
technical specifications indicated, and is committed for 12 months, starting from delivery date, to 
repairing or replacing the faulty part, component, equipment or part of it free of charge, returned 
to the manufacturer, unless the fault or malfunction is due to:
a) poor installation, even if conducted by qualified staff;
b) improper use of the product, due to lack of expertise, negligence or non-compliance with the 
operating instructions;
c) lack of or poor maintenance, even if carried out by qualified staff;
d) repairs or changes made by the purchaser on his own initiative;
e)   irregular   voltage   conveyance   of   the   power   lines,   insufficient   capacity   and/or   abnormal 
electrical installations;
f) abrasive or corrosive action of the physical or chemical agents;
g) poor or non-operation of the software or hardware or loss of data, registered by the purchaser, 
following storms, lightening, high temperatures or variation of electrical voltage, earthquakes, 
fires, etc.
The warranty also excludes all parts subject to normal wear, for which replacement is planned as 
ordinary maintenance.
In all cases in which the warranty remains excluded, as above given for example purposes, no 
compensation is due from M.G. srl for any damage caused to the purchaser and/or third parties 
due to use or poor operation of the product or for the period during which the system should 
remain inactive, as a result of faults and/or repairs, even if within the terms of warranty.
No indemnity will however be recognized for the purchaser or third parties for consequences 
deriving from no or improper functioning of the software and/or hardware, herein including direct 
and indirect damage.
For repairs or replacement, this part, component, equipment or part of it, must be sent/delivered 
to the manufacturer's plant on receipt of written authorization from M.G. industry srl and will not 
involve renewal of the period of warrant for the entire device, but only the relevant part.
The manufacturer reserves the right to make changes, at any time, to the equipment built and/or 
sold without being in any way obliged to make the same changes to the equipment previously 
built and/or sold.

 19     

Содержание TR-EVO

























Отзывы: