MFJ Plug&Play Intellituner -939 Скачать руководство пользователя | Manualshive

Страница: 36 / 40

background image

MFJ-939 Plug&Play IntelliTuner Automatic Antenna Tuner

Instruction Manual



2006-2015 MFJ Enterprises, Inc.

32

19.

Remove the cross-needle wattmeter from header HD1.

20.

Remove the transmitter/wattmeter and the 50-ohm dummy load from the tuner.

21.

Secure the cover back onto the tuner.

22.

Connect your transmitter to the TRANSMITTER connector and connect your antenna to the
ANTENNA connector on the tuner.

Jumper Settings

There are several sets of jumpers that can be used to configure the MFJ-939 to match specific radios and
functions. Jumpers not listed in this chart are reserved for future use.

0 is no jumper, 1 or a letter is a jumper installed, and X indicated a do not care setting.

Jumper JP1 is used to disconnect power from the interface cable to insure the radio does not power the
tuner if the radio can not supply the needed power.

Jumper

JP1

Function

0

Disconnects power from the interface cable

1

Connects power from the interface cable

Table 10 Jumper JP1 Setting

Jumper JP2 is used to set the MFJ-939 to the radio model in use. Note that no jumper disables the radio
interface.

Jumper

JP2

To Interface

Using Cable

0

No Radio Interface

--

I

Alinco
Icom
Yaesu FT-1000MP FT-2000
FT-9000
Yaesu FT-2000

MFJ-5114A

MFJ-5114I

MFJ-5114Y3
MFJ-5114Y3
MFJ-5114Y4

K

Kenwood

MFJ-5114K

Y

Yaesu FT-100 FT-450 FT-857
FT-897 FT-950

MFJ-5114Y

1

Reserved

--

2

Reserved

--

3

Reserved

--

4

Reserved

--

Table 11 Jumper JP2 Setting

Jumper JP4 is used to set a pull up resistor on tuner data lines when needed.

Jumper JP4

Function

0

Icom, IC-706, IC-707, IC-718, IC-725, IC-728, IC-736, IC-738, IC-746, IC-756, IC-7000

1

Kenwood TS-50S, TS-450S, TS-480HX, TS-570S, TS-590, TS-690S, TS-850S, TS-870S, TS-2000
Yaesu FT-100, FT-450, FT-847, FT-857, FT-897, FT-950

X

Yaesu FT-1000MP FT-2000 FT-9000
Alinco DX-70, DX-77, DX-701, DX-801

Table 12 Jumper JP4 Setting

«
...
34
35
36
37
38
...
»

Содержание Plug&Play Intellituner -939









































Отзывы:

Нет отзывов

Похожие инструкции для Plug&Play Intellituner -939

Бренд: Dimavery Страницы: 10

Бренд: Trust Страницы: 8

Бренд: KWorld Страницы: 8

ST1 smart tuner

Бренд: Russound Страницы: 12

Бренд: Teac Страницы: 32

Бренд: Onkyo Страницы: 8

Бренд: Palstar Страницы: 8

Бренд: Hama Страницы: 52

Бренд: TBS technologies Страницы: 23

Бренд: Panasonic Страницы: 64

Бренд: Magnum Страницы: 16

ENXTV-X2 EXTERNAL TV TUNER PRO

Бренд: Encore Страницы: 2

Бренд: i-PRO Страницы: 36

Бренд: Planet eStream Страницы: 4

Planet IPTV Streamer - Terrestrial (DVB-T) - Quad

Бренд: Planet eStream Страницы: 4

DIY599.com PA500

Бренд: DL4KA Страницы: 16

Бренд: Roku Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды