background image

FULL 12-MONTH WARRANTY 

MFJ Enterprises, Inc. warrants to the original owner of this product, if manufactured by MFJ Enterprises, 
Inc. and purchased from an authorized dealer or directly from MFJ Enterprises, Inc. to be free from 
defects in material and workmanship for a period of 12 months from date of purchase provided the 
following terms of this warranty are satisfied. 

1.

 

The purchaser must retain the dated proof-of-purchase (bill of sale, canceled check, credit 

card or money order receipt, etc.) describing the product to establish the validity of the warranty 
claim  and  submit  the  original  or  machine  reproduction  of  such  proof  of  purchase  to  MFJ 
Enterprises, Inc. at the time of warranty service.  MFJ Enterprises, Inc. shall have the discretion to 
deny  warranty  without  dated  proof-of-purchase.    Any  evidence  of  alteration,  erasure,  of  forgery 
shall be cause to void any and all warranty terms immediately. 

2.

 

MFJ  Enterprises,  Inc.  agrees  to  repair  or  replace  at  MFJ's  option  without  charge  to  the 

original  owner  any  defective  product  provided  the  product  is  returned  postage  prepaid  to  MFJ 
Enterprises,  Inc.  with  a  personal  check,  cashiers  check,  or  money  order  for 

$12.00 

covering 

postage and handling. 

3.

 

MFJ Enterprises, Inc. will supply replacement parts free of charge for any MFJ product 

under  warranty  upon  request.    A  dated  proof  of  purchase  and  a

  $8.00

  personal  check,  cashiers 

check, or money order must be provided to cover postage and handling. 

4.

 

This warranty is 

NOT

 void for owners who attempt to repair defective units.  Technical 

consultation is available by calling (662) 323-5869. 

5.

 

This warranty does not apply to kits sold by or manufactured by MFJ Enterprises, Inc. 

6.

 

Wired  and  tested  PC  board  products  are  covered  by  this  warranty  provided 

only  the 

wired  and  tested PC  board  product  is  returned.

   Wired  and tested  PC  boards  installed  in the 

owner's cabinet or connected to switches, jacks, or cables, etc. sent to MFJ Enterprises, Inc. will be 
returned at the owner's expense un-repaired.   

7.

  

Under  no  circumstances  is  MFJ  Enterprises,  Inc.  liable  for  consequential  damages  to 

person or property by the use of any MFJ products. 

8.

 

Out-of-Warranty Service: 

MFJ Enterprises, Inc. will repair any out-of-warranty product 

provided the unit is shipped prepaid.  All repaired units will be shipped COD to the owner.  Repair 
charges will be added to the COD fee unless other arrangements are made. 

9.

 

This warranty is given in lieu of any other warranty expressed or implied. 

10.

 

MFJ  Enterprises,  Inc.  reserves  the  right to  make  changes  or  improvements  in  design  or 

manufacture  without  incurring  any  obligation  to  install  such  changes  upon  any  of  the  products 
previously manufactured. 

 

11.

 

All  MFJ  products to  be  serviced  in-warranty  or  out-of-warranty  should  be  addressed  to 

MFJ Enterprises, Inc., 300 Industrial Park Rd, Starkville, Mississippi 39759, USA 

and must 

be accompanied by a letter describing the problem in detail along with a copy of your dated proof-
of-purchase and a telephone number. 

12.

 

This warranty gives you specific rights, and you may also have other rights, which vary 

from state to state. 

 

Rev 04/08/2011 

 
 

Содержание MFJ-950K3









Отзывы: