background image

20

Important:

 Adjustments can only be made while the mortar 

is still wet when correcting for squareness and leveling.

 

 

10. Assemble Dome Sides and Lower Rear Domes as shown 

in 

Figure 24

. The beveled face lines up with the inward 

angles of the lintel sides.    

 

Figure 24

Dome Side

Dome Side

Mid Lower 

Dome Rear

If you need to make adjustments, use shims between the 

lowest wall component and the top surface of the base plate. 

Once leveled, fill any resulting gaps with mortar.

11.   Assemble Upper Domes and Dome Sides as shown in 

Figure 25

. Check your assembly here. If things are 

proceeding as they should be, the finished top surface 

should be flat and level (

Figure 26

). 

Figure 25

Upper Dome

Upper Side 

Dome

Dome side 

faces to be 

flush

As you are connecting each Mason-Lite component, be certain 

you are following the instructions given previously for using 

Mason-Lite mortar. Stop to look at the smoke dome side, front 

and rear walls to see that they are aligning correctly and that 

the surfaces are smooth and uniform. Make sure connections 

are covered with an adequate amount of mortar. Remember 

that you have the option of using shims but they must be 

removed and any holes filled. Make any adjustments to the 

appliance alignment before continuing to the next step.

Figure 26

Top surfaces to be 

flush and level

12. Finally, set the Dome Top into position. Be sure that it is 

flush in every direction as you place it on the crest of the 

smoke dome wall assembly (see 

Figure 27

).

Figure 27

Make sure center of 

Ø12” B-Vent hole is 

centered.

Installing Draft Hood and Chimney System

Before installing your B-vent to the Mason-Lite Firebox you 

must install the draft hood (not supplied). The draft hood is 

pre-drilled with holes for four (4) cement Tapcon screws (not 

supplied).

1.  Place insulation blanket as shown in Figure 27.
2.  Place the draft hood on top of the appliance directly over 

the hole in top of the appliance and drill pilot holes for the 

Tapcon screws.

3.  Apply hi-temp silicone around the base of the draft hood 

and top of the appliance to create a good seal.

4.  Install the draft hood pressing draft hood into the silicone. 

Screw in the 4 Tapcon screws to hold draft hood in place.

Содержание Mason-Lite LMFP-108






































Отзывы: