Metrix DOX3104 Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 193

Metrix DOX3104 Скачать руководство пользователя страница 65

Functional Description

4-Channel SPO Digital Oscilloscopes

65

Functional Description

IV - ACQUISITION System (c

ont‟d)

Sequence Mode

In the

Sequence

mode, the recording memory is segmented. The oscilloscope captures

and records a waveform (

Frame

) at each trigger event. When the acquisition sequence is

completed, the oscilloscope displays the first 20 acquired waveform segments. In this
mode, the

“waveform capture speed” can reach up to 300000 waveforms/sec. When a

trigger event occurs, the oscilloscope acquires and records a waveform (segment) and
then waits for a new trigger event. The oscilloscope

“

blind time

” is minimized allowing the

capture of certain signal details, that were not visible with other acquisition modes.

For a 14Mpts maximum memory depth and with all four channels activated, the table
below shows the maximum number of Frames according to the « Time Base » coefficient :

Time Base

Coefficient

Sampling

Frequency

Current memory

Maximum

Frame Set

1ns/div

1.00GSPS

14pts

80 000

2ns/div

1.00GSPS

28pts

80 000

5ns/div

1.00GSPS

70pts

80 000

10ns/div

1.00GSPS

140pts

80 000

20ns/div

1.00GSPS

280pts

80 000

50ns/div

1.00GSPS

700pts

80 000

100ns/div

1.00GSPS

1.4kpts

63 157

200ns/div

1.00GSPS

2.8kpts

33 519

500ns/div

1.00GSPS

7kpts

16 042

1µs/div

1.00GSPS

14kpts

8 108

2µs/div

1.00GSPS

28kpts

4 067

5µs/div

1.00GSPS

70kpts

1 630

10µs/div

1.00GSPS

140kpts

815

20µs/div

1.00GSPS

280kpts

408

50µs/div

1.00GSPS

700kpts

163

100µs/div

1.00GSPS

1.4Mpts

81

200µs/div

500MSPS

1.4Mpts

74

500µs/div

200MSPS

1.4Mpts

74

1ms/div

100MSPS

1.4Mpts

74

2ms/div

50MSPS

1.4Mpts

74

5ms/div

20MSPS

1.4Mpts

74

10ms/div

10MSPS

1.4Mpts

74

20ms/div

5MSPS

1.4Mpts

74

50ms/div

2MSPS

1.4Mpts

74

100ms/div

1MSPS

1.4Mpts

74

200ms/div

500kSPS

1.4Mpts

74

500ms/div

200kSPS

1.4Mpts

74

1s/div

100kSPS

1.4Mpts

74

2s/div

50kSPS

1.4Mpts

74

5s/div

20kSPS

1.4Mpts

74

10s/div

10kSPS

1.4Mpts

74

20s/div

5kSPS

1.4Mpts

74

50s/div

2kSPS

1.4Mpts

74

Due to display limitations, the oscilloscope can not display more than 20 waveforms at a
time (

Overlay

» or «

Waterfall

» display modes) .

«
...
63
64
65
66
67
...
»

Содержание DOX3104


































































































































































































Отзывы:

Нет отзывов