METREL CE MultiTesterXA MI 3394 Скачать руководство пользователя страница 11

Страница: 11 / 39

MI 3394 CE MultiTesterXA

Instrument

operation

Measurement result is scaled to 110 V.

Red dot indicates phase of measurement where higher
leakage was measured. Applicable only if phase
reversal is enabled during the measurement.

Warning

A high voltage is / will be present on the instrument
output! (Withstanding test voltage, Insulation test
voltage, or mains voltage).

Warning

A very high and dangerous voltage is / will be present
on the instrument output! (Withstanding test voltage).

Test passed.

Test failed.

Conditions on the input terminals allow starting the
measurement; consider other displayed warnings and
messages.

Conditions on the input terminals do not allow starting
the measurement, consider displayed warnings and
messages.

Proceeds to next measurement step

Stop the measurement.

Содержание CE MultiTesterXA MI 3394








































Результаты поиска

Содержание CE MultiTesterXA MI 3394

Отзывы:

Похожие инструкции для CE MultiTesterXA MI 3394

Бренды по названию

Популярные бренды

METREL CE MultiTesterXA MI 3394, Руководство пользователя

Результаты поиска

Содержание CE MultiTesterXA MI 3394

Отзывы:

Похожие инструкции для CE MultiTesterXA MI 3394

Бренды по названию

Популярные бренды