background image

10    Conventional Products—B110LP Plug-In Conventional Low Profile Detector Base

Note: Do not use the tamper-proof capability if the XR2 removal tool

will be used to remove detectors from the base.

This detector base can be made tamper-proof so that the detector cannot be
detached without the use of a tool.

To make the base tamper-proof before installing the detector:

1.

Break off the smaller tab at the scribed line on the tamper-proof tab on
the detector mounting bracket (Figure 4).

tmprprf

Plastic Lever

Break tab at

dotted line by

twisting toward

center of base.

Figure 4:  Enabling the Tamper-Proof Feature

To remove the detector from the base after it has been made tamper-proof:

1.

Remove the decorative ring by rotating it in either direction and
pulling it away from the base.

2.

Insert a small screwdriver into the notch (Figure 5).

3.

Press the plastic lever toward the mounting surface before rotating the
detector counterclockwise for removal.

remdetct

Use small-bladed

screwdriver to

push plastic lever

in direction of arrow.

Figure 5:  Removing the Detector Head from the Base

The tamper-proof feature may be defeated by breaking and removing
the plastic lever from the base.  However, this prevents using the
feature again.

Tamper-Proof
Feature

Содержание B110LP













Отзывы: