background image

4

13)  Introduction  of  water  or  ice  from  any  source  into  the  oil/grease  may  cause 

overflow and severe burns from hot oil and water splatter. when frying with oil/

grease, all food products must be completely thawed and towel dried before 

being immersed in the fryer.

14)  never  drop  food  or  accessories  into  hot  cooking  liquid.  lower  food  and 

accessories  slowly  into  the  cooking  liquid  in  order  to  prevent  splashing  or 

overflow. when removing food from the appliance, care shall be taken to avoid 

burns from hot cooking liquids.

15)  this appliance and pot, including handles and lids, gets dangerously hot in use. 

use well-insulated pot holders or oven mitts for protection from hot surfaces or 

splatter from cooking liquids. safety goggles are also recommended to protect 

you from oil splatter. the oil remains dangerously hot hours after use.

16)  do  not  place  an  empty  cooking  vessel  on  the  appliance  while  in  operation. 

use caution when placing anything in the cooking vessel while the appliance is 

in operation. never use a cooking vessel larger than the capacity and diameter 

specified in this manual.

17)  In  the  event  of  rain,  snow,  hail,  sleet  or  other  forms  of  precipitation  while 

cooking with oil/grease, cover the cooking vessel immediately and turn off the 

appliance  burners  and  gas  supply.  do  not  attempt  to  move  the  appliance  or 

cooking vessel. 

18)  do not move the appliance when in use. Allow the cooking vessel to cool to 

100°F (38°c) before moving or storing.

19)  Avoid  bumping  of  or  impact  with  the  appliance  to  prevent  contact  with  hot 

appliance, spillage or splashing of hot cooking liquid. 

20)  see use and care section for lp gas cylinder Information. A 20 pound 

          (9  kg)  cylinder  should  be  used  with  this  cooker.  the  lp-gas  supply  cylinder 

used  must  have  a  protective  collar  and  must  be  constructed  and  marked  in 

accordance with the specifications for lp-gas cylinders of the u. s. department 

of transportation (dot) or the national standard of canada, 

can/csa-B339, 

cylinders, spheres and tubes for the transportation of Dangerous Goods. do 

not store a spare lp-gas cylinder under or near this appliance. never fill the 

cylinder beyond 80% full. For proper vapor withdrawal, the 20 lb. (9 kg) cylinder 

should be used in the proper upright position. cylinder must be turned off while 

not in use. Failure to follow these instructions and warnings could result in fire 

or explosion which could cause property damage, personal injury or death.

21)  this appliance is not intended for commercial use.

22)  use King Kooker

®

 appliances only in accordance with state and local ordinances, 

or in the absence of local codes, with the national Fuel gas code, 

ansiZ223.1/

nFPa 54, storage and Handling of liquefied Petroleum Gases, ansi/nFPa 58 or 

csa B149.1, natural Gas and Propane installation code.

FAIlure to Follow these InstructIons And wArnIngs could result In 

FIre, explosIon, burn hAzArd or cArbon monoxIde poIsonIng whIch 

could cAuse property dAmAge, personAl Injury or deAth.

Содержание 90SPK



















Отзывы: