Mercury Epiphone Valve Junior Скачать руководство пользователя страница 5

Страница: 5 / 47

Epiphone Valve Jr.

•

Mercury Upgrade Kit

This project and its documentation is the result of technical investigations made by the engineering staff of

Mercury Magnetics

. The disclosure of the information herein may pertain to proprietary rights and

the furnishing of these documents does not constitute an expresed or implied license to use such materials.

The Story Behind

Mercury’s

First Transformer Demonstration Project

ay back in ’06 your friends at

Mercury

set out to create a basic demonstration

to show exactly what quality

transformers

could do for your tone. Our goal

was to reveal the sonic capabilities of high quality

magnetics –

i.e.

properly designed

. generic

transformers

What started out as a simple educational demo

ended up blowing the minds of virtually everyone

who heard it. There was no denying how

extraordinary our little test amp sounded after

the

Mercury

trannys

were

installed....

The guinea pig

For the experiment we chose

Epiphone’s

remarkable value,

the all-tube

Valve Jr:

• 5 watts

• Single-ended, class A design

• One generic 12AX7 preamp

tube

• One generic EL84 power tube

• Generic

power

output

transformers

• No choke

Epiphone’s Valve Jr.

is an ideal demonstration

platform for our purposes because it is such a

fundamental, stripped-down tube amp. With no

digital components, no tone knobs, no added

f/x circuits, nothin’... you just can’t get any more

elementary and still have a playable tube amp!
All this for around $100.00–$150.00 retail? Yes, but

as you might expect, the stock amp is rather dull

and anemic-sounding.

The

Mercury Upgrades

The

Mercury

team spent about 3 months

working on the little amp before deciding upon the

best sounding combination of

Upgrades

and

adaptations.
The project was headed by

Sergio Hamernik

Mercury Magnetics

, and Los Angeles-

based amp wizard,

Alan Cyr.

After examining the

original circuitry several custom

Axiom

-series

transformers

and

Mini-Choke

sets were designed

and tested. Alan was then able to clean up the

circuit, effectively opening up the

amp’s sound because much of

the original circuit was designed

to get around and reduce noise

generated from the original

trannys – no longer necessary

by the

Mercury Upgrades

The result is a remarkably

toneful little amp that runs quiet

and sounds B-I-G.
If you are an experimenter you

may want to try different speaker

and/or tube configurations,

but oddly enough, those

components deliver relatively minor tonal changes

compared to the absolutely H-U-G-E improvement

of the

Mercury

trannys

Here in Los Angeles, the

Mercury Upgraded

Valve Jr.

is one of the hottest, most in-demand

insider amps around. Those who’ve heard it

immediately want one – and at such low cost to

make the mods, who can afford NOT too!
With this kit you’ll be able to transform your bland

little

Valve Jr.

into a keeper.

Continued on next page

Содержание Epiphone Valve Junior
















































Результаты поиска

Содержание Epiphone Valve Junior

Отзывы:

Бренды по названию

Популярные бренды

Mercury Epiphone Valve Junior, Инструкция по сборке

Результаты поиска

Содержание Epiphone Valve Junior

Отзывы:

Бренды по названию

Популярные бренды