Mercury Epiphone Valve Junior Скачать руководство пользователя страница 13

Страница: 13 / 47

Epiphone Valve Jr.

•

Mercury Upgrade Kit

This project and its documentation is the result of technical investigations made by the engineering staff of

Mercury Magnetics

. The disclosure of the information herein may pertain to proprietary rights and

the furnishing of these documents does not constitute an expresed or implied license to use such materials.

2-1/2”

2”

2“

1”

YELL

GREEN

YELL

2“

3”

2-1/2”

BLACK

YELLOW

BLACK

Attach to Output Jack

Module “GND” (ground)

Attach

to PCB

location “T4”

Attach to PCB

location “T3”

(left hole)

GREEN (4

Ω

)

YELLOW (8

Ω

)

GRAY (16

Ω

)

Attach to Output Jack

Module “4R”

Attach to Output Jack

Module “8R”

Attach to Output Jack

Module “16R”

SECONDARY

(OUTPUT)

PRIMARY

(INPUT)

Mercury Magnetics

9167 Independence Ave. • Chatsworth, CA 91311
(818) 998-7791 • FAX (818) 998-7835
info@

MercuryMagnetics

.com • www.

MercuryMagnetics

.com

100% of our products are designed & handmade in So. California, USA. • Established in 1954

(All dimensions are nominal)

EPJR-OM

MULTI-TAP VERSION

EPJR-OM

CLASS

: Axiom®

TYPE

: Output Transformer

PART NO.

: EPJR-OM

ORIGINAL EPIPHONE PART NO.

YW TF-VALVE JUNIOR-5W

MOUNTING

: Horizontal L-Bracket

POWER RANGE

: Our OTs are rated

to handle up to 50% more power than

the original manufacturer spec.

DATE

: 04-24-07

MUL
TI-T
AP

VERSION

licensed to Mercury Magnetics. Epiphone is a registered trademark of Gibson Guitar Corp. or its subsidiaries. Mercury Magnetics is not affiliated with Gibson Guitar Corp.

Epiphone Valve Jr.

Origin: Stock Valve Jr.
purchased in April 2005
specifically for modification
purposes.

Содержание Epiphone Valve Junior
















































Результаты поиска

Содержание Epiphone Valve Junior

Отзывы:

Бренды по названию

Популярные бренды

Mercury Epiphone Valve Junior, Инструкция по сборке

Результаты поиска

Содержание Epiphone Valve Junior

Отзывы:

Бренды по названию

Популярные бренды