manualshive.com logo in svg

Mercury Epiphone Valve Junior, Инструкция по сборке

Поделиться
Скачать
Mercury Epiphone Valve Junior Скачать руководство пользователя страница 20

20 

Epiphone V

alve Jr

.

 • 

Mercury Upgrade Kit

This
 project

 and
 its

 documentation

 is

 the
 result

 of

 technical

 investigations

 made

 by

 the
 engineering

 staf
f of

 

Mercury Magnetics

. The
 disclosure

 of

 the
 information

 herein

 may
 pertain

 to

 proprietary

 rights

 and
 

the
 furnishing

 of

 these

 documents

 does

 not
 constitute

 an

 expresed

 or

 implied

 license

 to

 use
 such
 materials.

T7 

T8 

T9 

T3 

V2 

V1 

T10 

T11 

T12 

GND 

C6 

C9 

C7 

C8 

T1 

T2 

D3 

T4 

T5 

R10 

R11 

T6 

B1 

C12 

D4 

D1 

D2 

IN 

G 

IN  S10  G 

VALVE JUNIOR 

VER051122 

HBO1570 

9 

8 

7 

6 

5 

4 

3 

2 

1 

1 

9 

8 

7 

6 

5 

4 

3 

2 

1 

1 

R12 

R14 

C3 

C5 

JP3 

C4 

R2 

R15 

R5 

R4 

R3 

C1 

R13 

R1 

R8 

JP1 

JP2 

R9 

R6  R7 

C2 

C11 

MAIN PCB PREP SEQUENCE:
1.  Remove clips (T1, 2, 3, 4, 5, 
 

6, 7, 8, 9, 10, 11 & 12).

2.  Remove rectifier (B1).
3.  Remove capacitors (C4 & 12).
4.  Remove resistors (

R

1*

, 7,  

8*

, 

 

9**

, 10, 11 & 12).

 

*Remove for Version 2 PCBs. 

 

  Do not remove for Version 3 PCBs.

 

**Remove for Version 3 PCBs. 

 

    Do not remove for Version 2 PCBs.

5.  Make 5 trace cuts as indicated.
6.  Drill new 5/64” holes as 
 

indicated (holes 1 to 6).

7.  If you will be installing the 

 

6V6 Mod 

then enlarge holes 

 

7 & 8 with 1/16” bit.

8.  Add 2 buss wire jumpers 
 

as indicated.

Hole 1 

Hole 2 

Holes 3 & 4 

Jumper 1 

Enlarge hole 7 

Jumper 2 

(before soldering, remove 

lacquer to reveal copper trace) 

Trace cut 1 

Trace cut 2 

Trace cut 3 

Trace cut 4 

Trace cut 5 

Holes 5 & 6 

Enlarge hole 8 

VERSION: 05-09-06 (original)
6V6 REV. 04-09-10 (updated)

www.MercuryMagnetics.com 

www.Amp-Exchange.com 

Copyright © 2008 by Mercury Magnetics. All Rights Reserved. Mercury Magnetics, 6V6 Mod and Mercury Upgrade are trademarks of Mercury Magnetics.  Epiphone is a registered trademark of Gibson Guitar Corp.  or its subsidiaries. Mercury Magnetics is not affiliated with Gibson Guitar Corp. 

Valve Jr. 

VERSION 2 & 3 MAIN PCBs 

Содержание Epiphone Valve Junior
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды