Mercury 300 - PRO MAX 3.0L Скачать руководство пользователя страница 73

Страница: 73 / 79

TROUBLESHOOTING

– ENGINE RUNS ERRATICALLY

POSSIBLE CAUSES

•

Spark plugs fouled or defective. Refer to Maintenance Section.

•

Incorrect setup and adjustments.

•

Fuel is being restricted to the engine.

a. Fuel injectors obstructed.

b. Fuel tank filter obstructed.

c. Water separating filter or In-Line filter clogged.

d. Stuck anti-siphon valve on built in fuel tank.

e. Fuel line is kinked or pinched.

Reed valve open or broken.

•

Fuel pump failure.

•

Ignition system component failure.

– PERFORMANCE LOSS

POSSIBLE CAUSES

•

Throttle not opening fully.

•

Damaged or improper size propeller.

•

Incorrect engine timing, adjustments, or setup.

•

Boat overloaded or load improperly distributed.

•

Excessive water in bilge.

•

Boat bottom is dirty or damaged.

Содержание 300 - PRO MAX 3.0L
















































































Результаты поиска

Содержание 300 - PRO MAX 3.0L

Отзывы:

Похожие инструкции для 300 - PRO MAX 3.0L

Бренды по названию

Популярные бренды

Mercury 300 - PRO MAX 3.0L, Руководство пользователя

Результаты поиска

Содержание 300 - PRO MAX 3.0L

Отзывы:

Похожие инструкции для 300 - PRO MAX 3.0L

Бренды по названию

Популярные бренды