Mercury 300 - PRO MAX 3.0L Скачать руководство пользователя страница 41

Страница: 41 / 79

OPERATION

Pre-Starting Check List

Operator knows safe navigation, boating/operating procedures.

An approved personal flotation device of suitable size for each
person aboard and readily accessible (it is the law).

A ring type life buoy or buoyant cushion designed to be thrown
to a person in the water.

Know your boats maximum load capacity. Look at the boat ca-
pacity plate.

Arrange passengers and load in the boat so the weight is distrib-
uted evenly and everyone is seated in a proper seat.

Tell someone where you are going and when you expect to
return.

It is illegal to operate a boat while under the influence of alcohol
or drugs.

Know the waters and area you will be boating; tides, currents,
sand bars, rocks, and other hazards.

Engine lowered to run position with all water intake holes sub-
merged.

Fuel tank vent cap open or fuel petcock “On”.

Fuel supply OK.

Oil supply (oil injection) OK.

Lanyard stop switch in “Run” position and cord connected.

Remote control in “Neutral”.

Top cowl latches secure.

Make inspection checks listed in the Inspection and Maintenance
Schedule. Refer to Maintenance Section.

Содержание 300 - PRO MAX 3.0L
















































































Результаты поиска

Содержание 300 - PRO MAX 3.0L

Отзывы:

Похожие инструкции для 300 - PRO MAX 3.0L

Бренды по названию

Популярные бренды

Mercury 300 - PRO MAX 3.0L, Руководство пользователя

Результаты поиска

Содержание 300 - PRO MAX 3.0L

Отзывы:

Похожие инструкции для 300 - PRO MAX 3.0L

Бренды по названию

Популярные бренды