Mercury 300 - PRO MAX 3.0L Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 79

background image

14

GENERAL INFORMATION

obj1

Selecting Accessories For Your Outboard

Genuine Mercury Marine Accessories have been specifically de-
signed and tested for your outboard.

Mercury Marine accessories are available from Mercury Marine
dealers.

Some accessories not manufactured or sold by Mercury Marine are
not designed to be safely used with your outboard or outboard oper-
ating system. Acquire and read the installation, operation, and
maintenance manuals for all your selected accessories.

WARNING

Check with your dealer before installing accessories. Misuse
of acceptable accessories or the use of unacceptable acces-
sories can result in serious injury, death, or product failure.

Safe Boating Suggestions

In order to safely enjoy the waterways, familiarize yourself with local
and other governmental boating regulations and restrictions, and
consider the following suggestions.

Use Life Jackets. Have an approved life jacket of suitable size for
each person aboard and have it readily accessible (it is the law).
However we strongly recommend that everyone aboard wear their
life jacket.

Do not overload your boat. Most boats are rated and certified for
maximum load (weight) capacities (refer to your boat capacity
plate). If in doubt, contact your dealer or the boats manufacturer.

Perform safety checks and required maintenance. Follow a reg-
ular schedule and ensure that all repairs are properly made.

Know and obey all nautical rules and laws of the waterways.
Boat operators should complete a boating safety course. Courses
are offered in the U.S.A. by (1) The U.S. Coast Guard Auxiliary, (2)
The Power Squadron, (3) The Red Cross and (4) your state boating
law enforcement agency. Inquiries may be made to the Boating Hot-
line, 1-800-368-5647 or the Boat U.S. Foundation information num-
ber 1-800-336-BOAT.

(continued on next page)

«
...
14
15
16
17
18
...
»

Содержание 300 - PRO MAX 3.0L
















































































Отзывы:

Нет отзывов

Похожие инструкции для 300 - PRO MAX 3.0L

56 Side Console

Бренд: YAMARIN Страницы: 37

288 EXPRESS FISHERMAN

Бренд: Albemarle Страницы: 122

Бренд: Hallberg-Rassy Страницы: 61

Бренд: Ockelbo Страницы: 64

Samba Jeanneau Sun Odyssey 45 2007

Бренд: Hermes Yachting Страницы: 26

1998 GTX RFI 5666

Бренд: Sea-doo Страницы: 26

Inflatable Boat

Бренд: Seamax Страницы: 38

Whitewater Series

Бренд: Dagger Страницы: 12

Бренд: FitNord Страницы: 84

Бренд: Rondar Raceboats Limited Страницы: 14

Бренд: Ranger Tugs Страницы: 36

Бренд: Rangertugs Страницы: 35

Бренд: Edgewater Networks Страницы: 17

Бренд: Edgewater Networks Страницы: 224

ST70 Instrument

Бренд: Raymarine Страницы: 42

Бренд: Gumotex Страницы: 40

Бренд: NorthStar Страницы: 52

42 Fly-Grande Coupe

Бренд: Regal Страницы: 386

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды