Mercury 300 - PRO MAX 3.0L Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 79

background image

5

ob

GENERAL INFORMATION

gob12

1

2

U.S. COAST GUARD CAPACITY

MAXIMUM HORSEPOWER XXX

MAXIMUM PERSON
CAPACITY (POUNDS)

XXX

MAXIMUM WEIGHT
CAPACITY

XXX

obc1

Boat Horsepower Capacity

1

Do not overpower or overload your boat. Most boats will carry a
required capacity plate indicating the maximum acceptable
power and load as determined by the manufacturer following
certain federal guidelines. If in doubt, contact your dealer or the
boat manufacturer.

WARNING

Overpowering a Boat Can Cause:

•

Serious injury, death, or boat damage.

•

Loss of Boat Control.

•

Flotation Characteristics of Boat to be Altered from Placing
Too Much Weight on Transom.

•

Boat to Break Apart, Particularly Around the Transom
Area.

obd2

High-Speed And High-Performance Boat
Operation

2

If you are not familiar with high-performance boat operation we
recommend that you first request an orientation/demonstration
ride with your dealer or an operator experienced with your boat/
outboard combination. Refer to the “Guide to Hi-Performance
Boat Operation” booklet (Part Number 90-849250) included in
your literature packet.

«
...
5
6
7
8
9
...
»

Содержание 300 - PRO MAX 3.0L
















































































Отзывы:

Нет отзывов

Похожие инструкции для 300 - PRO MAX 3.0L

Sun Odyssey 379

Бренд: Jeanneau Страницы: 154

2550 Console Cabin

Бренд: PURSUIT Страницы: 29

Бренд: Feathercraft Страницы: 8

Бренд: Mareplast Страницы: 5

Бренд: Ranger boats Страницы: 36

Бренд: Volvo Penta Страницы: 76

Бренд: SKEETA FOILING CRAFT Страницы: 32

Бренд: Pelican Страницы: 12

Бренд: Rave Sports Страницы: 16

WaveRunner VX Deluxe 2007

Бренд: Yamaha Страницы: 96

Бренд: Yamaha Страницы: 32

Бренд: Malibukayaks Страницы: 15

Бренд: NW Explorations Страницы: 58

Бренд: Weta Marine Страницы: 19

Ladoga 1 advanced

Бренд: Triton Страницы: 22

480 Sedan Bridge

Бренд: Sea Ray Страницы: 101

Бренд: Sea Ray Страницы: 210

Бренд: Sea Ray Страницы: 184

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды