background image

 

Mercury Security © 2015 

MR51e 

DOC  10107-0035  

REV 1.06 

 Page   5 

7.  Input Circuit Wiring: 

Typically, these inputs are used to monitor door position, request to exit, or alarm contacts.  Input circuits 
can  be  configured  as  unsupervised  or  supervised.    When  unsupervised,  reporting  consists  of  only  the 
open or closed states.   

When  configured  as  supervised,  the  input  circuit  will  report  not  only  open  and  closed,  but  also  open 
circuit,  shorted,  grounded*,  and  foreign  voltage*.    A  supervised  input  circuit  requires  two  resistors  be 
added to the circuit to facilitate proper reporting.  The standard supervised circuit requires 1K Ohm, 1% 
resistors  and  should  be  located  as  close  to  the  sensor  as  possible.    Custom  end  of  line  (EOL) 
resistances may be configured via the host software.  

*

 Grounded and foreign voltage states are not a requirement of UL 294 and therefore not verified by UL. 

 

The input circuit wiring configurations shown are supported but may not be typical:  

 

 

8.  Relay Circuit Wiring: 

Two Form-C contact relays are provided for controlling door lock mechanisms or alarm signaling.  The 
relay contacts are rated at 5 A @ 30 Vac/dc, dry contact configuration.  Each relay has a Common pole 
(C), a Normally Open pole (NO) and a Normally Closed pole (NC).  When you are controlling the delivery 
of  power  to  the  door  strike,  the  Normally  Open  and  Common  poles  are  used.    When  momentarily 
removing  power  to  unlock  the  door,  as  with  a  mag  lock,  the  Normally  Closed  and  Common  poles  are 
used.  Check with local building codes for proper egress door installation. 

Door lock mechanisms can generate feedback to the relay circuit that can cause damage and premature 
failure of the relay.  For this reason, it is recommended that either a diode or MOV (metal oxide varistor) 
be used to protect the relay.  Wire should be of sufficient gauge to avoid voltage loss. 

 

It is possible for the MR51e to provide power for a 12 Vdc door strike providing the maximum current is 
not exceeded, see specification section.  

 

 
 
 
 
 
 
 
 

1K,1%

1K,1%

1K,1%

1K,1%

Standard Supervised Circuit,
Normally Closed Contact

Standard Supervised Circuit,

Normally Open Contact

Unsupervised Circuit,
Normally Open Contact

Unsupervised Circuit,
Normally Closed Contact

TB2

IN4

IN2

IN3

1

IN1

TB1

1

}

 

Diode Selection: 

 

Diode current rating: 1x strike count 
Diode breakdown voltage: 4x strike voltage 
For 12 Vdc or 24 Vdc strike, diode 1N4002 
(100V/1A) typical. 

 

 

TB6

2-C

NC

NC
NO

1

NO
1-C

Содержание MR51e










Отзывы: